The computational capabilities of off-the - shelf wireless sensors networks presents a limitation when more complex forms of localization algorithms are employed for location estimation purposes, particularly in an indoor environment. Range-free algorithms rely on Received Signal Strength (RSS) from sensors that are location aware (anchor nodes) as the major means of distance estimation. This paper presents a non-site specific algorithm for better estimating RSS relationship with distance. By employing a unique form of rationalization of raw RSS with respect to distance using the proposed algorithm, it is possible to enhance the reliability of RSS when employed in indoor Localization Algorithms. Consequently, this paper presents an innovative RSS-Distance rationalization algorithm for localization of objects in an indoor environment. The paper compared the proposed algorithm with Simple Moving Average (SMA) algorithm due to the wide applicability and ease of manipulation of SMA. The analysis of the proposed algorithm and SMA shows that the proposed algorithm better modifies RSS for more accurate position estimation in an indoor environment.
Localization using wireless sensors relies on inter-nodal distance measurements between anchors using the coordinate system or the knowledge of the enclosed geographical environment. The measurements, using a typical WSN localization system can be related to the coordinates of sensors using the following generic formula:
S = h ( U ) + e (1)
where S is the vector of all the measurements, U contains the true coordinate vectors of sensors whose locations are to be estimated and e is the vector due to measurement errors [
RSS is a free resource that is exploited by both range-based and range-free algorithms, however, range-based algorithms are more accurate but they do require a higher computational cost and complexity than range free algorithm. WSN for range-based algorithms would require modification and consequently be more expensive than WSN devices for range-free algorithms [
The simplest form of measurement in WSN is connectivity measurements [
The objective of this paper is to establish a relationship between RSS and distance. The paper will be developed in two phases. The first phase will present a justification through experimentation that RSS is a reliable indicator or factor for localization. The second phase will present the RSS-distance normalization algorithm. Thus, the goal is to present an algorithm for processing RSS values towards a 2D node localization scheme in an indoor environment. Since RSS values are used for approximating the spatial position of the sensor nodes, hence, our interest in this method. This is because sensor nodes are freely equipped with RF modules for wireless communication, thus, no extra hardware will be required. The paper is organized as follows; a synopsis of related literature and related theory, a description of the experimental test-bed, RSS as a reliable connectivity index; RSS-distance normalization algorithm, making a comparative analysis with Simple Moving Average (SMA); discussion and findings, and lastly, concluding the paper.
From literature study of indoor localization, it is established that most approaches to localization rely on a form of RSS for offline training using a priori fingerprinting information corresponding to the reference nodes. Some methods such as Maximum Likelihood Estimate (MLE) are also well documented [
In this particular work, the Cramer-Rao Lower bound and MLE were derived for algorithms based on TOA and RSS. This requires that all devices in the network provide estimated range between themselves and their neighboring reference nodes. Localization accuracy is largely dependent on anchor or node densities. Hence, accuracy could become an issue in low density networks. On the other hand, large data overhead could negatively impact data transmission rate and life span of the network.
The effects of antenna polarization on localization accuracy of objects in an indoor environment were examined. The research established that the accuracy of localization was significantly related to the position of range measurement [
Various forms of weighted algorithms were also proposed. Basically, a rational attenuation exponent was developed, then the position of the targeted node is established through a form of centroid localization [
Some RSS-based location estimation algorithm for WSN combines Generalized Regression Neural Network (GRNN) and weighted centroid localization (WCL). To mitigate the instability of RSS, they proposed real-time training scheme that was capable of adapting to the changes in channel characteristics of WSN. They opined that the scheme was flexible and could match the spatial and temporal changes in wireless channel environment. In the algorithm, reference sensor nodes were permanently installed in some known locations. RSS measurements at all the access points (AP) from the reference sensors and their known locations (two dimensional coordinate data) were separately used to train two GRNN networks separately. After estimating the approximate location of the unknown node and its neighbors using GRNN, the final estimation is done by WCL [
Although existing literature review on the reliability of RSS is inexhaustible, nevertheless, there is a general agreement that raw RSS values in an indoor environment are unreliable with respect to distance. Also, what is clear from the foregoing is that most algorithms do rely on RSS in one form or another for finger printing or terrain mapping to estimate location. However, to the best of our knowledge there is no proposal to directly alter the reliability of RSS with respect to distance, prior to its direct application to localization. Consequently, our proposed algorithm seeks to fill this gap.
Ranging methods focus on estimating the distance between a transmitter and a receiver, by exploiting known signal characteristics. For instance, nodes that are location unaware (free nodes) that are within the communication range (radii) of anchor nodes, can use the RSS from the anchors for distance estimation. If the anchors signal strength is known, along with the attenuation law for signal strength as a function of distance, then the receiver node can use RSS to estimate its distance from the sender [
- Reflection from smooth surfaces or metallic objects.
- Superposition of electromagnetic fields.
- Diffraction.
- Refraction.
- Diffusion.
- Absorption.
- Polarization of electromagnetic fields.
- Receiver circuit.
In free space, received signal strength is inversely proportional to the square of the distance between two sensors. The free space model provides a measure of path loss as a function of transmitter-receiver (T-R) separation when the transmitter and receiver are within line-of-sight (LOS) range in a free space environment. The model is given by Equation (3) which represents the path loss as a positive quantity in dB.
R S S ∝ 1 ( d i s t a n c e ) 2 (2)
P a t h L o s s ( d ) = − 10 log 10 [ G t G r λ 2 ( 4 π ) 2 d 2 ] (3)
where G t and G r are the ratio gains of the transmitting and receiving antennas respectively, λ is the wavelength in meters, and d is the Tx-Rx separation in meters. However, the free space path loss equation provides valid results only if the receiving antenna is in the far-field. The far-field is defined as the distance d f given by Equation (4).
d f = 2 D 2 λ (4)
where D is the largest linear dimension of the antenna. For a receiver to be considered in the far-field of the transmitter, it must satisfy d f ≫ D and d f ≫ λ . Hence, Equation (3) is not applicable in our situation. Nonetheless, in reality, RSS is highly affected by changes in environmental conditions particularly in an indoor environment. Some of the factors that cause signal strength attenuation make RSS not to correlate with distance, and some of the factors change from one enclosed medium to another. Hence, providing a generalized RSS model that could be applicable in all indoor conditions would be very difficult.
RSS or received power, P r , is related to distance, d and is given by the log-distance path loss model, which assumes that path loss varies exponentially with distance. The path loss in dB is given by Equation (5)
P r P t = G t ⋅ G r ( λ 4 π d ) (5)
where, P r is received power, P t is transmitted power, G t and G r are transmitter and receiver antenna gains respectively. λ is the wavelength of the signal transmitted and d is distance between antennas. This equation is called the Friis equation. Thus, Equation (6) can be modified as a log-normal shadow model as follows,
P ( d ) [ dBm ] = P ( d 0 ) [ dBm ] − 10 γ log 10 ( d d 0 ) + X σ (6)
where P ( d 0 ) represents the transmitting power of an anchor node at a reference distance d 0 and d the distance between the anchor and the object to be localized, γ is the path loss exponent and X σ is the shadow fading which follows zero mean Gaussian distribution with σ as standard deviation.
Shadowing is due to obstructions caused by hills and buildings, and will be of little effect in our case study, while multipath fading due to the constructive and destructive interference of transmitted signal will be of significance in an indoor environment. Hence, considering that we are interested in indoor localization, particularly in the context of this paper, where we expect the size of a room or hall way to be between 16 m2 and 25 m2, and a maximum distance of not more than 20 m between the transmitters and receivers, the effect of X σ can be neglected. Thus, Equation (7) will be modified as the log-distance path loss model, which assumes that path loss varies exponentially with distance.
P ( d ) [ dBm ] = P ( d 0 ) [ dBm ] − 10 γ log 10 ( d d 0 ) (7)
Consequently, the function of received signal, f ( R S S , γ ) could be estimated. The value of the path loss exponent γ varies depending upon the environment. In free space, it is equal to 2 [
In this section we outlined the methodology applied to obtain the RSS measurements required for RSS-distance estimation. We also describe the location in which the measurements were carried out. One of the main purposes of this research is to propose a reliable non site specific mechanism for estimating RSS relationship with distance. Consequently, the succeeding experiments were conducted to establish that there exists a relationship between RSS and distance that could be explored towards developing an algorithm for the manipulation of RSS data in location estimation.
A major problem in indoor localization is mapping RSS to distance, as each indoor environment presents its own unique challenges with regards to the irregularities of RSS with respect to distance. Fashioning a procedure to manipulate RSS values from location aware nodes (anchors) will be of great significance to the effectiveness of the application of WSN in indoor localization. This section describes the testbeds used in conducting the four experiments relevant to our RSS-Distance algorithm. Two of the experiments were carried out using Xbee radios while the other experiment was carried out using Micaz sensor nodes.
In our experiments, we used both Xbee radios and Micaz sensor nodes, both of which use the more advanced CC2420 radio chip and comply with IEEE 802.15.4 WSN standards. CC2420 operates in 2.4 GHz Industrial, Scientific and Medical (ISM) band, with an effective data rate of 256 kbps, which is a much higher rate than older radios (see
In the 2.4 GHz band, the CC2420 has 16 channels, with each channel occupying a 3 MHz bandwidth with a centre frequency separation of 5 MHz for adjacent channels. The radio chip uses an encoding scheme that encodes 32 chips for a symbol of 4 bits. The encoded data is then OQPSK (offset quadrature phase shift keying) modulated. The CC2420 radio chip provides useful information on RSS. Using micaz and Xbee radio (both of which use CC2420 chip), the experiment was conducted in Fraser Noble building at the University of Aberdeen with minimal human interference. Nevertheless, interference was generated by the persons taking readings of the radios from the sensor nodes. The received signal is analyzed with regards to the received signal power levels (RSS in dBm). The measurements were taken at various distances.
R S S = 10 log P ( d 0 ) P ( d ) [ R S S ] = dBm (8)
As earlier stated, the experiments were conducted in two phases. The first phase was to simply establish that RSS could provide a level of reliability as an indicator for localization. The second phase was conducted to generate a reasonable level of data to enable the modeling of RSS-distance normalization algorithm.
Radio | Platforms | Data Rate | Keying | Encoding |
---|---|---|---|---|
TR1000 | Mica | 13.3 kbps | ASK | SEC DED |
CC1000 | Mica2 | 19.2 kbps | BFSK | Manchester |
CC2420 | Micaz, Telos, Intel Mote2 | 256 kbps | OQPSK | Spread Spectrum |
This experiment was conducted for the purpose of establishing the level of connectivity and reliability of RSS values between transmitter and receiver. Two Xbee radios and two laptops were used in the experiment; one radio was configured using a laptop as the Coordinator and the second was configured as the Router. The X-CTU software tool, which is used for running range test was used to configure the radios. ZigBee protocol standard was used as the protocol for communication between the radios. RSS readings were taken at various distances from the Coordinator to the Router and vice-versa, also, the theoretical received power was calculated for each corresponding distance.
The first experiment using Micaz was set-up to analyze variation in connectivity of free sensor node from a single anchor. The anchors and base station (free sensor node) used in the experiment are made by CrossBow. The sensors were MicaZ MTS 420, while the base station was MIB520. The software, MoteView, a graphical user interface (GUI) based on TinyOS, was used to configure the 3 MicaZ sensor nodes used in the experiment. The MIB520, acting as a base station (BS) was connected to a laptop through a USB port, to be able to measure desired data using the MoteView. This set-up forms an XMesh network. The XMesh network requires that a node be programmed with the BS to form a single unit in order to be able to receive data from the three MicaZ nodes.
Distance (m) | Theoretical Rx | Coordinator Rx | Router Rx |
---|---|---|---|
1 | −30.9 | −49 | −50 |
3.1 | −40.8 | −50 | −50 |
6.2 | −46 | −53 | −55 |
9.89 | −50 | −56 | −56 |
12.99 | −53.3 | −58 | −58 |
16.09 | −55.2 | −53 | −53 |
Distance (m) | Node 1 (dBm) | Node 2 (dBm) | Node 3 (dBm) |
---|---|---|---|
1.35 | −69 | −62 | −75 |
2.50 | −69 | −66 | −69 |
3.14 | −76 | −69 | −76 |
3.25 | −70 | −70 | −78 |
5.25 | −86 | −79 | −82 |
The second experiment was conducted to analyze the variation in connectivity between a cluster of anchors and a free sensor node. Using 9 MicaZ sensors; one as a base station and the other 8 as two separate clusters, with each cluster comprising four sensor nodes. Each cluster covers a geographical space of about 16m2 and the cluster about 7 m apart from each other. The base station was stationed about 2 m away from one cluster at Location 1 and about 5 m from the other cluster at Location 2. Fifteen RSS data samples were recorded for each cluster. Using Matlab, the 15 RSS sample readings concurrently taken from 2 different cluster was modeled as a 200 data sample for each cluster. Each data sample was the average reading of the 3 highest RSS values from each cluster.
We conducted experiments to investigate the reliability of RSS in localization. Consequently, we set out to measure the RSS values of Xbee radios and MicaZ sensor nodes with respect to distance. The experiments and all measurements were performed in Fraser Noble Building, University of Aberdeen. The Xbee radios and micaz nodes were placed 1.45 m above the laboratory floor level and the radios were in line of sight. For the two Xbee radios, we transmitted packets at various distances (between 0 and 17 m), and collected RSS values of the two radios at various distances using the X-CTU software. Least-square regression analysis was carried out on the data and the regression equation is as given below:
Y = − 13.3 − 0.626 X 1 − 0.53 X 2 − 0.66 X 3 (9)
From the least-square regression analysis conducted on the collated data, the adjusted R-square values for the two graphs were reasonably high. The adjusted R-square is an indication of observed variation. Variability in actual radio transmission patterns can have a substantial impact on localization accuracy depending on the localization technique. Unlike the theoretical perfect circles, measured reception distance of radios can vary substantially with environmental conditions and antenna irregularity. However it is documented that proximity based algorithms are substantially unaffected by variation [
Also, when the average value of the RSS for the two Xbee radios in the first experiment were used as shown in
Our second experiment was conduct strictly for the purpose of validating our findings from the first experiment with Xbee radios. All the sensors were configured with the MoteView. RSS values as shown in
Y = − 11.3 − 0.0309 X 1 − 0.210 X 2 − 0.0319 X 3 (10)
However, it should be noted that there were no physical obstructions between the radios. Nonetheless, the findings in this experiment shows that proximity based algorithms can use RSS as an indicator for localization. The small variations in RSS measured could be attributed to channel variations. This finding is significant, as it shows the positive trend in the level of hardware calibration in the radios employed in WSN. It further buttress the fact that with better calibration, RSS can be used as a key location estimator in localization.
In the second experiment using Micaz, an analysis of the plot shows that the deviation of the cluster of anchors closer to the reference sensor was lower than the deviation of the cluster of anchors farther from the reference sensor (2.317 and 4.795 for the closer and farther clusters respectively).
In addition, the range between the maximum and minimum RSS values between the clusters closer to the reference sensor was 7 dBm as compared with 16 dBm for the clusters farther away from reference sensor. These values should be expected because range estimation error, when it can be quantified, is typically proportional to range such that short range measurements are more accurate within a few meters than longer range measurements. RSS measurement for ranging is a near versus far technique that can provide fairly accurate information about proximity but less accurate with regards to true range. This connectivity variation forms the basis of our algorithm. A knowledge of precise distance is not essential using connectivity, what is important is that the algorithm provides information about the relative positions of objects of interest within a known enclosed geographical space.
The objective of the algorithm is to establish a best fit relationship between RSS and distance. The aim of our proposed method is to smooth out the irregularities,
due to multipath effect in the link quality as indicated by the RSS. The idea is to determine a best fit RSS-distance value over a pre-determined window size. In our case study, each sampled average is over a window size of three consecutive RSS values that are between 0.5 m and 1 m distance apart.
There is a direct correlation between the error margins in localization and the distance intervals selected for RSS sampling [
This experiment was conducted to collate RSS data over given distances in an enclosed environment, given that it was established from the two preceding experiments that RSS was a good connectivity indicator. Two Xbee radios were configured for this experiment. Using the X-CTU software, one radio was configured as the Coordinator while the other was the Router. The Coordinator served as the anchor radio while the Router was employed as the radio of the free node to be localized. The radios were operated at 2.4 GHz and at full power. The transmission power of the radio was 1 mW (0 dBm), with a receiver sensitivity of −92 dBm.
The radios were placed on a flat surface 1.2 m above ground level. The hall way used for the experiment was unevenly shaped with different objects and equipment placed along the hall way. The sides walls were made of a combination of materials such as, bricks, wooden surfaces and metals. RSS readings were taken at 0.5 m intervals over a distance of 12 m.
Xbee radios have an estimated indoor transmission range of 30 m with a receiver sensitivity of −92 dBm. Signal readings were taken between 0.5 m and 12 m at intervals of 0.5 m, which are certainly within the transmission range of the radios. The choice of distance limitation for the experiment was to ensure that RSS readings were consistent and repeatable within the same experimental set-up. Hence, the RSS values in
Y = 20 log 10 X − 39 (11)
where γ = 2 in free space and d d 0 = X . Based on the data collected, we can express distance as X(m) and the measured RSS as Y(dBm) for the test bed area. We therefore, set our reference datum using Equation (12), which is the log-distance model for the propagation of the RSS data in free space. We compared the log-distance model with the simple moving average model and our proposed model.
The objective of this method was to check for consistency, which can be deduced by observing the standard deviation of each process from the idealized RSS model. Since the standard deviation in each distance estimate is directly proportional to the increment of the true distance to the transmitter, thus, the accuracy of the resulting location estimate depends directly on the standard deviation [
XY Coordinates (m) | RSS (dBm) |
---|---|
0.5, 0 | −39 |
1.0, 0 | −48 |
1.5, 0 | −51 |
2.0, 0 | −49 |
2.5, 0 | −55 |
3.0, 0 | −56 |
3.5, 0 | −52 |
4.0, 0 | −53 |
4.5, 0 | −48 |
5.0, 0 | −54 |
5.5, 0 | −54 |
6.0, 0 | −50 |
6.5, 0 | −53 |
7.0, 0 | −60 |
7.5, 0 | −51 |
8.0, 0 | −51 |
8.5, 0 | −53 |
9.0, 0 | −53 |
9.5, 0 | −61 |
10.0, 0 | −62 |
10.5, 0 | −60 |
11.0, 0 | −58 |
11.5, 0 | −61 |
12.0, 0 | −62 |
Equation (12) was used to generate the log-distance RSS values from the raw RSS values. Using Matlab, the regression model of the measured data (raw data) and the ideal log-distance path loss is as shown in
As seen from the graph, the combined influence of reflection, diffraction, and scattering causes multipath effects. At some points, the multipath signal components combine at the receiver to form a distorted version of the transmitted waveform. The signals could combine constructively or destructively depending on phase variations of the component signals. The destructive combination of the multipath components results in attenuated received signal at points where RSS is less than the corresponding log-distance value and constructive where the RSS value is greater than the log-distance value.
Two major factors of the plots where selected for analysis; the standard deviation and the range between the minimum and maximum RSS values in each plot. This is as shown in
As expected, propagation of radio signal has a log-normal distribution in free space, hence an idealized RSS value will steadily decrease with distance logarithmically. The log-distance value has a larger range of RSS values than the experimental values. Also, the log-distance plot has a larger standard deviation than the experimental values. There is very little information that could be inferred from this comparison because the idealized log-normal plot pattern is expected to be consistent, while the actual signal plot would change based on environmental conditions. Nonetheless, in this particular plot, the effect of signal amplification of the experimental RSS data resulted in a smaller range between RSS values and this is significant as it influenced a better standard deviation than that of the idealized log-distance model.
Simple Moving Average (SMA) is an unweighted mean of a set of data, it is used to identify a trend or direction of a set of data. SMA ensures that variation in the mean are aligned with the variation in the data. The major appeal of the SMA is the ease with which it can be calculated. An advantage to the limited processing and energy power of off the shelf sensor nodes. In our situation, given the set of measured RSS values obtained at the receiver, over a maximum distance of 12 m from the transmitter at intervals of 0.5 m. This situation is depicted in
For a set of RSS values, the SMA for a group of equally weighted data with a window size of three is;
R S S k = a k − 1 + a k + a k + 1 3
which can be represent by the Equation (12) below;
R S S k = 1 3 ∑ k n − 1 a k − 1 + a k + a k + 1 (12)
where n and k are positive integers and n = k + 1 .
A regression model of SMA along with the original model of the raw RSS values and the ideal log-distance value is as shown in
Experimental RSS data | Ideal log-distance data | |
---|---|---|
STD | 4.206 | 5.862 |
Range | 14 | 20.83 |
Experimental RSS data | SMA data | |
---|---|---|
STD | 4.206 | 3.62 |
Range | 14 | 15 |
In our experiment, we took measurements at 0.5 m intervals, which ensured that we were able to compare three discrete signal measurements that were within a 0.5 m radius. As earlier noted, the major problem with signal measurement in an indoor environment is the consistency in the RSS-distance relationship. Hence, the focus of our proposed algorithm was to enforce a level of consistency. Thus, three discrete and sequentially measured signals will be compared, and the maximum RSS value of the compared RSS data will be selected, this process will be repeated until all the observed data are considered.
In our case, the RSS values at 1.0 m, 1.5 m and 2.0 m were compared and the maximum of these values selected for the 1.0 m position. These same steps will be repeated to get a new RSS value for the position 1.5 m, given a set of discretely measured RSS signals taken at a sample interval of 0.5 m;
R S S n = a 1 , a 2 , a 3 , ⋯ , a n
Hence, selecting the first three measured RSS data, the new RSS, X 1 will be;
X 1 = | max { a 1 , a 2 , a 3 } |
likewise;
X 2 = | max { a 2 , a 3 , a 4 } |
X k = | max { a k , a k + 1 , a k + 2 } |
where n and k are positive integers; and k + 2 ≤ n . We applied our proposed algorithm to the measured RSS data and applied regression model to compare it with the original RSS data and the ideal log-distance data. This is displayed in
Using our proposed algorithm,
Indoor conditions make RSS-distance relationship fairly unreliable. The objective of most algorithms is to create a form of consistency between RSS and distance. A correlation between RSS and distance that is very similar in characteristics with the idealize model or propagation of RSS in free space is desired. In this case, we have an idealized situation using the log-distance model. Consequently, the best algorithm as presented in this paper will be the algorithm that best replicates the characteristics of the log-distance model. Therefore, the key characteristics that will be the focus of our discussion will be range and standard deviation. Using
Experimental RSS data | Proposed Algorithm data | |
---|---|---|
STD | 4.206 | 4.358 |
Range | 14 | 21 |
STD | Range | STD Difference | Range Difference | |
---|---|---|---|---|
Measured data | 4.206 | 14 | 1.656 | 6.83 |
Log-distance | 5.862 | 20.83 | - | - |
SMA | 3.62 | 15 | 2.242 | 5.83 |
Proposed Algorithm | 4.358 | 21 | 1.504 | 0.17 |
In this paper, range is a measure of the log-normal decay of the RSS values with respect to distance. It will be misleading to use the experimental RSS data as the reference data, as the nature of this data will change based on environmental conditions. What is consistent and expected is a log-normal decay of RSS with increasing distance in free space. Therefore, a good algorithm will seek to modify experimental RSS data to reflect the ideal log-distance model. The algorithm should be close in value to the log-distance data. In our experiment, looking at
The second value is the standard deviation. The standard deviation indicated in
RSS is a free WSN resource for localization, however, with a high level of uncertainty when used in its raw form for indoor distance estimation and consequently, poor localization estimates. Experiments were conducted to establish that RSS was a reliable connectivity index that could be manipulated for location estimation. The main idea behind our algorithm was to select the best fit RSS value within a range of relatively small contiguous set of raw RSS values called a window size. This was to ensure consistency between RSS and distance and also to reduce outlier effects in RSS-distance values. We observed that this approach improved the trend of RSS-distance relationship when compared with an idealized radio wave propagation model. It is believed that the proposed RSS-Distance algorithm when applied to raw RSS data prior to localization will reduce location estimation errors.
We believe that this novel procedure will improve localization of objects both indoors and outdoors. Nonetheless, we are aware that the proposed algorithm still needs to be subjected to experimental rigors, where RSS is a key determinant factor for location estimation. However, we believe this process will be of significant relevance to proximity based algorithms such as centroid localization algorithm. Furthermore, it is also believed that this algorithm will have strong application towards improving the accuracy of other range-based algorithms with respect to distance estimation, especially range-based algorithms that use Time of Arrival (TOA) for estimation. This possible field of application could form the basis for future research.
The author declares no conflicts of interest regarding the publication of this paper.
Ademuwagun, A. (2019) RSS-Distance Rationalization Procedure for Localization in an Indoor Environment. Wireless Sensor Network, 11, 13-33. https://doi.org/10.4236/wsn.2019.112002