In adaptive beamforming system adaptive algorithm of digital filter is applied to update the weighting vector of the antenna elements to get antenna gain along the desired direction and attenuation along the jammer. The objective of the paper is to evaluate the threshold gain of the adaptive beam former along the line of sight (LOS) between the transmitter and the receiver (including jammer suppression) to make the single hop link comparable with 2-hop link. The single hop and 2-hop communication systems are compared in context of symbol error rate (SER) under fading condition theoretically and verified by simulation. Finally we evaluate the numerical value of threshold gain of adaptive beamformer of two antenna elements under Rayleigh and Nakagami- m fading conditions.
To combat the fading affect of long wireless link, 2-hop model is widely used where a relay is placed between transmitter and receiver. The concept is applicable to enhance the performance of point to point link. The combined SNR of two links becomes approximately parallel combination of two SNRs like equivalent parallel resistor of electrical circuit. Therefore the combined SNR is less than the individual SNR (between transmitter and repeater or repeater and receiver) but the SNR between the transmitter and receiver (without the repeater station) is much less than the combined SNR of 2-hop wireless link. This phenomenon attracts the researcher to apply the concept of multi-hop in wireless networks to reduce SER and enhance throughput. The performance analysis of two-hop wireless link in context of BER under fading is discussed in [
The main objective of AAS is to combine the radiation pattern of individual antenna element (with proper weighting factor and phase shift) to produce a combined beam of desired directivity and gain. The detail analysis of AAS is found in [
The paper is organized like: Section 2 provides the theoretical analysis of dual-hop wireless link in determination of overall SNR, Section 3 deals with concept of AAS, overall SINR (signal to interference and noise ratio) at receiving end and algorithms of adaptive beamforming; Section 4 provides the results based on theoretical analysis of Section 3; and Section 5 concludes the entire analysis.
First of all we consider the 2-hop wireless link of
The received signal vector at the relay is expressed as:
y R = E H S R x + n S R , (1)
where E is the transmitted power, H S R is the channel matrix from the source to relay, x is the signal vector of source, and n S R is the noise vector of source to relay link. Above expression is applicable for MIMO system but for single antenna system instead of signal vector we consider individual symbol (for example symbols of 16-QAM) of transmitter and instead of channel matrix we consider simply channel gain may be complex number. When the signal is detected at relay, it is processed and transmitted with some delay expressed as: y ′ R D hence the received signal vector at the destination is,
y D = E H R D y ′ R D + n R D (2)
The noise vector on both the links are uncorrelated and possesses the properties: Ε ( n S R n S R † ) = I N R N 0 and Ε ( n R D n R D † ) = I N D N 0 , where N 0 is the variance of the additive white Gaussian noise (AWGN), I N R is the identity matrix with NR antennas at the relay station and ND is the number of antennas at the destination.
If the SNR of the links are: Γ S R = E S ‖ H S R ‖ 2 / N 0 and Γ R D = E ¯ R ‖ H R D ‖ 2 / N 0 , then the overall SNR will be [
Γ S D = Γ S R Γ R D Γ S R + Γ R D + 1 (3)
This overall SNR will be compared with overall SNR of AAS with adaptive beamformer under single hop of same path length.
For single antenna case Equations (1) and (2) is written conventionally like:
y R = P h S R x + n S R (4)
y D = P h R D y ′ R + n R D (5)
where each variable indicates a real or complex number instead of vector.
Once combined SNR γ c = Γ S D is evaluated then the SER under awgn is expressed as [
P s ( γ c ) = a Q ( 2 b γ c ) (6)
where γ c is a r.v. and the integers a and b depend on type of modulation scheme. Above analysis under fading channel is expressed as,
P s ( γ c _ a v ) = ∫ 0 ∞ P s ( γ c ) f Γ c ( γ c , γ c _ a v ) d γ c (7)
where f Γ c ( γ c , γ c _ a v ) is the pdf of r.v. of small scale fading channel and γ c _ a v is the average value of the r.v. In this paper we consider only Nakagami-m fading channel. For example for Nakagami-m fading case the pdf becomes,
f Γ c ( γ c , γ c _ a v ) = m m γ c m − 1 γ c _ a v m Γ ( m ) e − m γ c 2 / γ c _ a v (8)
We can use Equations (7) and (8) to evaluate SER under Nakagami-m fading case.
In array antenna system the number of antenna elements is a vital factor to achieve a wide variation of directivity and gain visualized from
Extraction of the original signal from a noisy environment is achieved by Finite Impulse Response (FIR) or Infinite Impulse Response (IIR) filter but their coefficients remain fixed during entire operation. In adaptive filter, adaptive
algorithms are used to adjust the coefficients of the digital filter so that the difference between the noisy input signal, Xk and the desired signal, d called the error signal ε attains at minimum value. The common algorithms found widespread applications are the least mean square (LMS), the recursive least squares (RLS), and the Kalman filter algorithms. In terms of computational complexity and storage requirements, the LMS algorithm is the most efficient but the Kalman filter is suitable for immunity of any type of noise at the expense of process time. To enhance the gain of the antenna array in the direction of desired signal and to provide attenuation in the direction of interference or multiple jammer we use adaptive algorithm of IIR and FIR filter. An adaptive filter consists of FIR/IIR and adaptive algorithm to adjust the weighting factor of each branch of signal discussed in [
Let us now provide the way of enhancement of gain in desired direction and elimination of jammers using the concept of adaptive beamforming. We will then determine the threshold gain of the beamformer under a single hop wireless link to be comparable with case of 2-hop link in context of SER. In adaptive beam former two types of omni antennas are used 1) primary antenna 2) reference antenna. Both types of antennas receive signal and interference/jammer. Each reference antenna element is associated with adaptive filter and its weight is adjusted in such a way that it can receive only jammer where the primary antenna provides the sum of signal and jammer. Now the jammer part of the primary antenna is correlated with the output of reference antenna hence the error between primary and reference antenna provides the required signal component. The weighting factors of reference antenna elements are updated using adaptive algorithms of [
To match with multiple jammers of different direction at the same time, it is necessary to have more than one reference omni as explained in [
Radiation pattern of two reference adaptive beamforming is shown in
The overall SINR at receiving end is, Γ 0 = P r ⋅ G d ∑ j = 1 k I j ⋅ A j + N 0 ≈ Γ ⋅ G (9)
where Pr is the received signal power along desired direction, Gd is gain of the AAS along the link between Tx and Rx, Aj is the gain along the jth jammer, Ij is the interference/jammer along jth direction and N0 is the awgn noise. Overall SINR is approximated as Γ ⋅ G ; where Γ is the SNR of conventional single antenna system and G is the ratio of Gd and Aj.
In free space path loss model the received signal at a distance d is expressed as: P r = K ⋅ P t ⋅ d − α ; where α is path-loss exponent. Therefore if the distance is increased to twice of the previous one then the received signal or SNR is decreased by a factor of 2−α. The overall SNR of 2-hop wireless link (distance of each is d) is approximately half of SNR of single hop link of distance d. If the enhancement of overall gain G of the array antenna system is greater than 2−α-1 then the proposed scheme of the thesis brings the desired result will be verified in next section. Such concept is available in [
In this algorithm we use the concept of Wiener filter theory in minimization of mean square error of cost function which actually represents the difference between output of the adaptive filter and desired output. For input signal u(n) and kth weighting factor Wk the output signal from a linear combiner is given as,
y ( n ) = ∑ k = 0 M − 1 W k * u ( n − k ) (10)
Output power,
P = | y ( n ) | 2 = ∑ k = 0 M − 1 ∑ i = 0 M − 1 W k * W i E [ u ( n − k ) u ( n − i ) ] = ∑ k = 0 M − 1 ∑ i = 0 M − 1 W k * W i r ( i − k ) (11)
where E [ u ( n − k ) u ( n − i ) ] = r ( i − k ) is the autocorrelation function.
If the beamformer is subjected to a linear constraint, ∑ k = 0 M − 1 W k * e − j θ 0 k = g ; then
the real valued cost function becomes,
J = ∑ k = 0 M − 1 ∑ i = 0 M − 1 W k * W i r ( i − k ) + Re [ λ * ( ∑ k = 0 M − 1 W k * e − j θ 0 k − g ) ] (12)
where g is the complex-valued gain, θ0 desired electrical angle of arrival.
Taking gradient of J and putting the result equal to zero like Wiener filter theorem, we get the optimum weighting vector like,
W 0 = g * R − 1 S ( θ 0 ) S H ( θ 0 ) R − 1 S ( θ 0 ) (13)
where S ( θ 0 ) = [ 1 e − j θ 0 e − j 2 θ 0 ⋯ e − j ( M − 1 ) θ 0 ] is known as steering vector and its details are found in [
Considering uniform linear array of N = 6 antenna elements the variation of normalized power (dB) against the azimuth angle is shown in
The steering vector corresponding to
S = [ − 0.9971 − 0.0760 i 0.8350 − 0.5503 i − 0.3234 + 0.9462 i − 0.3234 − 0.9462 i 0.8350 + 0.5503 i − 0.9971 + 0.0760 i ] T
This algorithm is an extension of previous one where the desired and undesired signals are analyzed separately. A widely used method of adaptive beamforing is LCMV (linearly constraint minimum variance) algorithm where the weighting vector of adaptive filter is divided into two portion Wq and Wa. Here the first one is dependent on desired signal i.e. signal along the desired AOA (Angle of Arrival) and the second one is related to sidelobe and un-correlated with the desired signal. A constraint matrix Ca correspond to a band rejection filter is used to segregate the sidelobe from the desired signal shown in
Winner filter theorem is applied to in getting weighting vector for minimum output y(n).
Let us introduce multiple linear constraints by the constraint matrix C and gain vector g like,
C H W = g (14)
where the overall weight vector is, W = W q − C a W a
The desired signal of the beamformer,
d ( n ) = W q H ⋅ U ( n ) ; where W q = C ( C H C ) − 1 g (15)
If Ca is a stop band FIR filter with zero response in desired direction θ0 then the signal with sidelobe is C a H U ( n ) = x ( n ) and the output signal is y ( n ) = d ( n ) − W q H x ( n ) .
Applying Winner filter theorem,
W a = ( C a H R C a ) − 1 C a H R W q (16)
where R is the autocorrelation matrix of input vector.
Taking the following parameters under LCMV: SNR = 50 dB, carrier frequency fc = 1 GHz, the number of antenna elements N = 10, antenna spacing λ/2 and elevation angles 0˚ we get the following response (using simulation of LCMV in Matlab 13) for different AOA and directions of jammer (azimuth angle) shown in
The weighting vectors for above 4 cases are evaluated as:
W 1 = [ − 0.0489 − 0.1267 i 0.0443 + 0.1161 i − 0.0540 − 0.0985 i 0.0322 + 0.0688 i − 0.0176 − 0.1005 i − 0.0264 + 0.0665 i 0.0128 − 0.0669 i − 0.0613 + 0.1043 i 0.0407 − 0.1328 i − 0.0558 + 0.1188 i ] T
W 2 = [ 0.0680 − 0.0776 i 0.0364 + 0.0809 i − 0.0568 + 0.0648 i − 0.0782 − 0.0738 i 0.0767 − 0.0872 i 0.0847 + 0.0737 i − 0.0767 + 0.0672 i − 0.0731 − 0.0556 i 0.0619 − 0.0593 i 0.0786 + 0.0830 i ] T
W 3 = [ 0.0452 − 0.0686 i − 0.0665 + 0.0640 i 0.0487 − 0.0840 i − 0.0318 + 0.0945 i 0.0142 − 0.1566 i − 0.0035 + 0.1070 i − 0.0446 − 0.0866 i 0.0445 + 0.0989 i − 0.0491 − 0.0701 i 0.0633 + 0.0493 i ] T
W 4 = [ − 0.0009 − 0.0962 i − 0.0208 + 0.0956 i − 0.0021 − 0.1051 i 0.0014 + 0.0879 i − 0.0004 − 0.1425 i − 0.0111 + 0.0963 i − 0.0161 − 0.0788 i − 0.0055 + 0.1134 i − 0.0096 − 0.1043 i 0.0049 + 0.0833 i ] T
In this paper the matric used against the performance of wireless link is SER or
BER for single and 2-hop cases.
Finally we compare the theoretical and simulation results regarding 2-hop and single hop AAS under QPSK modulation scheme. We use Rayleigh and Nakagami-m fading condition with bit rate of 9.6 Kbps and Doppler shift of 100 Hz. First the simulation is done for 2000 random symbols shown in
The relative performance between Rayleigh and Nakagami-m is found subtle for SNR in the range of 0 dB to 20 dB. To observe the variation we plot BER
against SNR in the range of −10 dB to 0 dB shown in
The weak radiation of the antenna is strengthened and made more directional using antenna array. The performance of single hop link is compared with 2-hop
link of same distance using adaptive array antenna system. The results of the paper highlighted the threshold gain of the array required to meet the condition of 2-hop wireless link. In this paper we use exponential path loss model suitable for suburban area or a link of short distance applicable in ad-hoc network or femto cell of LTE. Still we have the scope to enhance the model for conventional path loss model of fading channel. The analysis of the paper will be helpful for a wireless network planner to choose the optimum antenna for coverage of WLAN and WMAN.
The authors declare no conflicts of interest regarding the publication of this paper.
Rahaman, A.S.Md.M., Akhter, J., Jani, Md.R. and Islam, Md.I. (2018) Determination of Array Gain of Single Hop to Achieve the Performance of a 2-Hop Wireless Link. Journal of Computer and Communications, 6, 84-98. https://doi.org/10.4236/jcc.2018.67008