The development and implementation of advanced analytical technologies is essential for extending the expiry for complex drug products stored in the Strategic National Stockpiles. Consequently, a novel Ultra High-Performance Liquid Chromatographic (UHPLC) method has been developed for the analysis of atropine and its respective impurities to support the analytical research platform for auto-injectors. This study is part of a larger research effort to improve the efficiency and broaden the applicability of advanced analytical methods for medical counter-measure medications. The current HPLC compendial methodology for atropine sulfate injection requires an analysis time of 40 minutes for atropine. In comparison, the novel gradient UHPLC method required only 8 minutes to evaluate both atropine and its major pharmaceutical impurities. Improved separation was achieved on a Waters Acquity UHPLC BEH C18 1.7 μm, 2.1 × 100 mm column employing gradient elution of mobile phase solvent A (0.1% H 3PO 4) and solvent B (0.1% H 3PO 4, 90% ACN, and 10% H 2O). The method was validated according to USP Category I requirements for assay. The daily standard calibration curves were linear over a concentration range from 50 μg/mL to 250 μg/mL with a correlation coefficient of >0.999. The detection limit (LOD) and quantitation limit (LOQ) were 3.9 μg/ml and 13.1 μg/ml, respectively. Resolution results indicate that atropine and the following impurities, degradants and a preservative can also be separated and analyzed using this proposed method: noratropine, 4,4’-di-hy-droxydiphenyl ether, 2,4’-dihydroxydiphenyl ether, 4-bromophenol, 4-hydro-xyatropine, tropic acid, apoatropine HCl, atropic acid, hydroquinone, nitroethane, phenol and catechol. The UHPLC method demonstrated enhanced selectivity and significantly reduced the analysis time when compared with the traditional USP compendial HPLC method. The method was successfully applied to the evaluation of atropine in ATNAA auto-injectors lots from the Strategic National Stockpiles.
The Department of Defense (DoD) and Food and Drug Administration’s (FDA) Shelf Life Extension Program (SLEP) (http://www.fda.gov/EmergencyPreparedness/Counterterrorism/MedicalCountermeasures/MCMLegalRegulatoryandPolicyFramework/ucm411446.htm) represents a unique partnership between the DoD and the FDA’s Center for Drug and Evaluation Research (CDER) and the Office of Regulatory Affairs (ORA). This program is designed to save the federal government and the US taxpayer significant monetary resources by selecting products purchased by DoD and testing them for potency and stability to extend their effective shelf life beyond expiry. FDA has developed and operated a scientifically sound program that can determine whether, and for how long, a specific lot of a specific drug product will continue to meet applicable quality standards after it has reached its labeled expiration date [
Drugs tested in this program range from antibiotics to antidotes for various poisoning agents [
ATNAA is an auto injector drug-device product designed to deliver a prefilled, single intramuscular dose of atropine and pralidoxime chloride in a self-contained unit [
Pralidoxime chloride has its most critical effect in relieving paralysis of the muscles of respiration. Because pralidoxime is less effective in relieving depression of the respiratory center, atropine is always required concomitantly to block the effect of accumulated acetylcholine at this site. Pralidoxime relieves muscarinic signs and symptoms, salivation, bronchospasm, etc.; but this action is relatively unimportant since atropine is adequate for this purpose Published reports have established the safety and efficacy of atropine and pralidoxime chloride used separately, as well as the safety and increased efficacy of atropine and pralidoxime chloride when administered concomitantly in the treatment of nerve agent poisoning in humans [
Numerous stability studies have shown that pralidoxime and atropine sulfate is remarkably stable at room temperature measured by HPLC after 10 years [
[
important to understand the pharmaceutical chemistry to anticipate the separation and analysis requirements of these complex set of impurities [
In the past, analytical techniques such as HPLC have been employed for the analysis of atropine and its impurities [
introduction of new high resolution chromatographic techniques such as UHPLC, a new, simple, selective, and efficient method with an extended linear range and enhanced sensitivity for atropine and its related impurities has been developed. UHPLC is a relatively recent technique in liquid chromatography that is being more broadly applied to complex pharmaceutical drug products. The primary advantages for wide scale pharmaceutical use include significant reductions in analysis, time, resolution and solvent consumption [
In this paper, we present a validated method for the rapid quantitative determination of atropine and its potential impurities based on UHPLC methodology. Until now, no exhaustive UHPLC chromatographic method for analysis of atropine and its potential impurities has been described. Previous studies have analyzed atropine by itself without impurities using a UHPLC method [
Acetonitrile (UPLC grade), phosphoric acid and glacial acetic acid were purchased from Fisher Scientific, (Fair Lawn, NJ). Sodium acetate, catechol, nitroethane, hydroquinone, noratropine, 2-bromophenol, 4-bromophenol and tropic acid were purchased from Sigma Aldrich (St. Louis, MO). Tetra butyl hydrogen sulfate was purchased from Acros (Pittsburgh, PA) and 5N sodium hydroxide from EMD chemicals (Darmstadt, Germany). Atropine sulfate United States Pharmacopeia reference standard was purchased from USP (Rockville, MD). Apoatropine HCl and atropic acid were purchased from Meridian (Columbia, MD). All other chemicals were of reagent grade, and the water was obtained from the Thermo Scientific Barnstead Genpure Pro and Millipore Milli-Q water systems.
A Waters Alliance 2695 HPLC (Milford, MA) with 2489 UV/Visible detector, solvent manager and sample manager was used. Separation was achieved on HPLC C-18 column, 4.6 × 250 mm 5-micron 80A. Column temperature was mentioned at 25˚C. The chromatographic conditions for the USP 37 HPLC method were the following: flow rate of 2 mL/min, isocratic run, 100% mobile phase consisting of 5.1 g of tetrabutylammonium hydrogen sulfate with 50 mL of acetonitrile, dilute with Acetate buffer to 1 L and adjust pH to 5.5 with 5 N NaOH. The HPLC method was validated (data not shown) and then transferred to UHPLC.
A Waters Acquity H-Class UHPLC (Milford, MA) with a photo-diode array (PDA) detector, quaternary solvent and sample manager was used. Separation was achieved on a Waters Acquity (Wexford, Ireland) BEH C18 1.7 μm, 2.1 × 100 mm column. The chromatographic conditions for the method were the following: flow rate of 0.55 mL/min, mobile phase consisting of solvent A (0.1% H3PO4) and solvent B (0.1% H3PO4, 90% acetonitrile, 10% H2O) with the following gradient (
The column temperature was controlled at 50˚C, and the injection volume was 1.0 µL. The UV detection wavelength was 220 nm, and the run time was 7 minutes.
The initial stock standard calibration solution was created with a concentration of approximately 250 μg/mL. 6.25 mg of atropine sulfate was weighed out in a 25.0 mL volumetric flask. The flask was then filled with Milli-Q water to two-thirds volume with water and then sonicated and shaken for 5 minutes at 37˚C and 75 RPM. Using the stock standard solution (~250 μg/mL), the following calibration solutions were then prepared by serial dilution: 200, 100, 75 and 50 μg/mL.
The initial stock QC solution was created with a concentration of approximately 250 μg/mL. 6.25 mg of atropine sulfate was weighed out in a 25.0 mL volumetric flask. The flask was then filled with deionized Milli-Q water to two-thirds volume with water and then sonicated and shaken for 5 minutes 37˚C and 75 RPM. Using the stock standard solution (250 μg/mL), the following quality control standards were then prepared by serial dilution: 100 and 50 μg/mL.
The following compounds were weighed accurately and separately into 25 mL volumetric flasks each and diluted up to volume with Milli-Q water (scale down
Time (minutes) | Solvent A (%) | Solvent B (%) |
---|---|---|
0.00 | 84 | 16 |
2.20 | 84 | 16 |
2.21 | 65 | 35 |
5.00 | 65 | 35 |
5.10 | 84 | 16 |
7.00 | 84 | 16 |
as necessary): 3.0 mg noratropine, 1.5 mg hydroquinone, 1.5 mg catechol, 3.0 mg of 2,4’-dihydroxydiphenyl, 3.0 mg of 4,4’-dihydroxydiphenyl ether, 3.0 mg of nitroethane, 1.5 mg of tropic acid, 1.75 mg of apoatropine, 1.5 mg of atropic acid, and 3.0 mg of 4-bromophenol.
1) To create the final impurity mix, 2 volumes of noratropine were diluted with 1 volume of each impurity standard into separate flasks.
2) The individual impurities can be stored for later use, but the final impurity mix must be mixed fresh prior to use.
Sample content from one ATNAA injector equivalent to approximately 2.1 mg atropine) was transferred into a 10.0 mL volumetric flask and diluted up to volume with Milli-Q water. System suitability experiments were performed to demonstrate linearity, precision, and accuracy, as per USP <621> Chromatography [
The method was validated according to the United States Pharmacopeia <1225> Validation of Chromatographic Methods-Category 1 requirements for Assay as well as a limits test for the impurities. The following validation characteristics were addressed: precision, accuracy, linearity, range and specificity.
System suitability standard solution was prepared daily from the stock atropine sulfate solution and the phenol standard solution (0.1971 mg/mL and 0.2467 mg/mL respectively). System suitability was determined from six replicate injections of the system suitability standard before sample analysis. Based on USP <621> and regulatory specifications for limits, the acceptance criteria were the following: less than 2% relative standard deviation (RSD) for the peak area of six consecutive injections, greater than 2000 theoretical plates, USP tailing factor less than 2.0, resolution of peaks greater than 2, and capacity factor (k’) greater than 1.0.
Standard calibration curves were prepared with five calibrators over a concentration range of 50 - 250 µg/mL (50, 75, 100, 200 and 250 µg/mL) for atropine sulfate. The data of peak area versus drug concentration were treated by linear least square regression analysis. The standard curves were evaluated for intra- and inter-day linearity. The analytical range was established by the highest and lowest concentrations of analyte where acceptable linearity, accuracy and precision were obtained.
Accuracy and precision of the method were determined for atropine sulfate: the QC standard samples at three concentrations of atropine (low QC 50, intermediate QC 100, and high QC 250 µg/mL Precision was expressed as a coefficient of variation percentage (CV %) of the analyte peak.
Specificity of the method was determined by observing that there were no co- eluents with atropine or its major impurities.
Three different lots of ATNAA auto-injectors stored in the SNS were evaluated for potency and impurities of atropine.
The UHPLC System is an advanced chromatographic technology that is designed to improve the resolution of complex chemical mixtures. This is generally achieved by minimizing band spreading within column and taking advantage of sub 2 micron particle size columns. UHPLC technology presents an important opportunity for the separation, identification and determination of major and minor or potential impurities of atropine present in parenteral pharmaceutical dosage forms. This study supports the goal of advancing the research platform for auto-injectors to enhance regulatory monitoring capabilities and control risk for stockpiled drug products. Here, it was demonstrated the potential minor and major impurities were not able to be efficiently resolved by HPLC methodology. However, following a simple method transfer, potential minor and major impurities were effectively resolved by UHPLC (Figures 2-5).
The primary objective of the present study was aimed at developing a sensitive, precise and accurate UHPLC method for analysis of atropine and its respective impurities in auto-injector drug products. Initially, the atropine assay was performed using the traditional USP 37 method for atropine sulfate injection to establish a baseline for chromatographic outcomes including analysis time, tailing, selectivity, resolution, etc. As seen in Figures 2-5, the HPLC analysis time is 40 minutes for the run to resolve the atropine and phenol peaks; but the analysis time can take over 70 minutes when trying to resolve the atropic acid peak as well (
In order to achieve enhanced separation, for both major and minor impurities and a less complex mobile phase, the USP 37 method was transferred to a UHPLC system without salt composition in the mobile phase. Selected gradient were screened to resulting in the noted gradient that resolved all the impurities with dramatically increased efficiency.
The USP system suitability test was conducted daily and the method was validated according to USP <1225> validation of chromatographic methods for the UHPLC method. The system suitability test included also included the impurities and the results indicated no change in retention time for the respective impurities. This test provided assurance that the method was reproducible despite the significant gradient change between 2.0 and 2.1 minutes. The resolution parameter Rs for atropine and tropic acid was evaluated and found to be consistent over the three day validation period. Ruggedness testing was conducted with multiple analysts and multiple instruments using the system suitability test and the method was found to be rugged.
The UHPLC method was able to achieve the separation of all four impurities including tropic acid 1.5 min vs. 18 min, apoatropine HCl 3 min vs. 26 min, and most notably atropic acid 3 min vs. 72 min. The chromatography is highlighted in Figures 7-9. The following impurities were also analyzed simultaneously using the UHPLC method: noratropine, 4,4-dihydroxydiphenyl ether, 2,4-dihydro- xydiphenyl ether, 4-bromophenol, 4-hydroxyatropine, tropic acid, apoatropine HCl, atropic acid, hydroquinone, nitroethane, phenol and catechol. The chromatographic results for the various impurities are shown in
The system suitability test evaluates the daily operating parameters of the analytical system including the resolution between different peaks of interest. All critical parameters tested met the acceptance criteria on all days (
The system suitability test for the analytical UHPLC method established instrument performance operating parameters such as retention time, peak area, capacity factor, and USP tailing factor for the atropine sulfate peak. All validation
USP criteria | Specifications | Day 1 | Day 2 | Day 3 | Pass/Fail |
---|---|---|---|---|---|
Retention time | RSD ≤ 2.0% | 1.3 | 1.3 | 1.3 | Pass |
Capacity factor k’ | >1.0 | 1.6 | 1.6 | 1.6 | Pass |
Area | RSD ≤ 2.0% | 0.2 | 0.2 | 0.2 | Pass |
Theoretical plates | >2000 | 4208 | 4238 | 4215 | Pass |
USP tailing | <2.0 | 1.8 | 1.8 | 1.8 | Pass |
Resolution* | >2.0 | 3.2 | 3.3 | 3.4 | Pass |
*Resolution calculated based on atropine sulfate and tropic acid peak.
parameters tested met the acceptance criteria on all days.
The following method validation characteristics were addressed for atropine sulfate: accuracy, precision, specificity, linearity and range. The validation characteristics met the acceptance criteria for USP Category I.
Linearity of the method was confirmed by preparing atropine sulfate standard curves for the analytical range of 50 - 250 µg/mL. A correlation between analyte peak area and concentration of the drug was observed with r2 ≥ 0.9999 for the standard curves (
Accuracy and precision were established across the analytical range for atropine sulfate. The accuracy and intra- and inter-day precision were calculated from the QC samples for atropine sulfate. Results for the intra-day accuracy of atropine sulfate are summarized in
The analysis of the mobile phase (solvent A: 0.1% H3PO4, solvent B: 0.1% H3PO4, 90% acetonitrile, 10% H2O) solution showed the absence of any major peaks beyond the void volume (
The validated method was successfully applied for the evaluation of three different lots of ATNAA as shown in
Standard curve | Range (μg/mL) | Calibrators | Slope | y-intercept | R2 value |
---|---|---|---|---|---|
Day 1 | 50 - 250 | 5 | 993.30 | −2079.5160 | 1.0000 |
Day 2 | 50 - 250 | 5 | 999.60 | −2489.2502 | 1.0000 |
Day 3 | 50 - 250 | 5 | 1002.79 | −2022.8564 | 1.0000 |
Validation (QC) solutions (μg/mL) | ||||
---|---|---|---|---|
50 | 100 | 250 | ||
Accuracy (% recovery) | Day 1 | 100.6 | 100.0 | 100.1 |
Day 2 | 101.4 | 100.4 | 100.9 | |
Day 3 | 100.5 | 99.7 | 100.5 | |
Precision (% RSD) | Day 1 | 0.4 | 0.4 | 0.4 |
Day 2 | 0.6 | 0.2 | 0.2 | |
Day 3 | 0.6 | 0.5 | 0.4 |
Test | Specifications | Lot 1 | Lot 2 | Lot 3 |
---|---|---|---|---|
Atropine (% declared) | (90 - 115)% | 99.6 | 97.9 | 96.9 |
Phenol (mg/mL) | NLT 0.5 mg/mL | 2.99 | 3.03 | 3.02 |
% Tropic acid | NMT 2.0% | 1.06 | 1.01 | 0.98 |
% Apoatropine | NMT 0.5% | 0.23 | 0.22 | 0.2 |
% Atropic acid | NMT 0.5% | ND | ND | ND |
% Hydroquinone | NMT 2.0% | 0.05 | 0.04 | 0.04 |
% Nitroethane | NMT 2.0% | ND | ND | ND |
% Catechol | NMT 1.0% | 0.13 | 0.09 | 0.1 |
% Noratropine | NMT 2.0% | ND | ND | ND |
% 4,4’-Dihydroxy | NMT 1.0% | 0.06 | 0.06 | 0.06 |
% 2,4’-Dihydroxy | NMT 1.0% | 0.05 | 0.05 | 0.04 |
% 4-Bromophenol | NMT 2.0% | 0.05 | 0.05 | 0.05 |
% 4-Hydroxy | NMT 1.0% | 0.25 | 0.21 | 0.21 |
Each of the 3 separate lots met the USP specifications for potency and impurity limits. The method takes advantage of the resolution enhancement of UHPLC to fully describe the related and degradation and excipient impurities in a complex formulation auto-injector drug product.
The compendial HPLC method for atropine was implemented and evaluated for efficiency and suitability to assess an atropine auto-injector drug product and its impurity profile. The USP 37 HPLC method was found to require analysis run times up to 80 minutes, especially in product samples with the associated complex impurity profile. A simple, sensitive and accurate UHPLC method was developed for the efficient resolution and quantitatation of atropine and its respective impurities of atropine auto-injector formulations. The developed UHPLC method was found to be rapid (8 min run time), accurate and sensitive. The analytical method was validated to ensure compliance in accordance with USP <1225> guidelines.
The UHPLC method was directly compared with the compendial HPLC method described in the USP37. The proposed UHPLC method demonstrated enhanced resolution along with the capability for simultaneous analysis of atropine and its related degradants, impurities and formulation excipients. The method was successfully applied for the analysis of atropine and its impurities in stockpiled ATNAA auto-injector samples.
In summary, this method can be used for efficient testing control strategies as well as lifecycle management to evaluate the extended stability analysis of atropine and its respective impurities for drug products stored in the SNS. The information on extended product stability beyond expiry is unique and the use of advanced analytical technologies such as UHPLC will provide greater scientific and regulatory understanding of failure and evaluating risk for stockpiled products.
This project was supported in part by intramural CDER Office of Testing and Research funding.
Yen, C.H., Mohammad, A., Schneider, M., Poole, S.K., Lowry, B., McCurdy, B.W., Faustino, P.J. and Khan, S.R. (2017) Development and Application of a Validated UHPLC Method for the Determination of Atropine and Its Major Impurities in Antidote Treatment Nerve Agent Auto-Injectors (ATNAA) Sto- red in the Strategic National Stockpiles. Pharmacology & Pharmacy, 8, 15-31. http://dx.doi.org/10.4236/pp.2017.81002