This paper deals with implementation of Sinusoidal Pulse-Width-Modulation (SPWM) for a single-phase hybrid power filter generator for Photovoltaic (PV) and wind grid applications. Using policy iteration algorithm, an improved variable step-size perturbation and observation algorithm is contrived and it is implemented proficiently using a hard-ware description language (VHDL) (Very High Speed Integrated Circuit Hardware Description Language). Subsequently, the new generated grid source supplements the existing grid power in rural houses during its cut off or restricted supply period. The software is used for generating SPWM modulation integrated with a solar-power & wind power grid system which is implemented on the Spartan 3 FPGA. The proposed algorithm performs as a conventional controller in terms of tracking speed and mitigating fluctuation output power in steady state operation which is shown in the experimental results with a commercial PV array and HPW (Height Weight Proportional) show. Simulation results demonstrate the validity with load of the proposed algorithm.
The basic requirement of the electrical energy is incessantly growing in consistent with the rapid growth of population and the increasing usage of the electrical gadgets. Diminishing trend of raw material resources has made the conventional grid supply standstill and inert in the grid connected areas. The further extension of convention grid supply is not possible due to various technical, political and economic reasons. Owing to the excess energy demand, alternative renewable energy sources like solar/ wind etc. are being used with energy storage device i.e. Battery which works as a standalone power source or in sharing mode with Grid or DG power source. Between the two sources, solar energy is highly preferred because it is easily available in every part of the country where as wind energy is restricted only to the coastal area. A hybrid system structure is shown in
get fully charged from a single PV source. Hence the solar power system needs to be integrated with supplementary additional DG back up sources for attaining 24 hour power supply. Adding more number of PV modules and battery bank, the system can work as a standalone power source in a grid deprived area in remote rural sectors. The optimal utilization of these sources is possible with efficient smart adaptive Power converter and adopting optimal load management. In the present paper, the Pulse width modulated (PWM) adaptive intelligent Power converter (inverter) the PWM pulses are directly generated using a new technique through software program coded with VHDL and downloaded in FPGA Spartan 3E starter kit to produce base drive signals for inverter power device. The FPGA VLSI technology offers a fast system with many more advantages as compared to other conventional technology etc. The software program can easily be changed to optimize and control the inverter parameters like frequency, voltage amplitude, number of PWM pulses in half cycle etc, without changing the hardware circuit.
The system works under three modes of operation namely:
Ø Charging Mode (PV/Grid during sun hour available Period);
Ø Inverting Mode (Grid Cut off or restricted (load shedding) Period).
The operation is controlled optimally (during the period when the system does not support to deliver power to load).
The Simulink structure of PV module is shown in
proportionately with the grid/windmill source using time regulator circuit through sinusoidal PWM bi-directional inverter for meeting the required end user load energy demand. The typical characteristics of PV array are shown in
Ø Windmill mode (the power is generated from the wind turbo which has higher harmonics level. Thus, harmonics level is reduced and it is converted from AC to DC).
Typical Characteristics of a PV array.
Wind Systemturbine the output power obtained as,
The mathematical relation for mechanical power extraction form the wind turbine can be expressed as
where
As the paragraph’s title suggests, perturbing control variable voltage operates P&O algorithm and comparing the instantaneous grid output power after perturbation with previous outputs. In a controller using P&O method the adjustment of the operating point is achieved by changing the reference voltage of the controller. However, the adjustment can be made through the duty ratio. Note that V(k) and P(k) are output voltage and the power of the grid which is calculated from V(k) × I(k) at time k, respectively.
To achieve faster Height Weight Proportional response and more accurate MPP under dynamic environment, variable step-size voltage has to be merged with source.
Hybrid system is an integrated system which can be operated under changing natural conditions to provide a quality power supply to remote areas. The system utilizes different renewable energy sources altogether such as solar energy, wind energy, or micro hydropower. The profuse energy is available in renewable sources which can be harnessed and converted as electricity in a sustainable way to supply the necessary power to the people without accessing the electricity grid. On accessing the hybrid system in
remote areas, the cost of transported fuel can be avoided and it has less effect on climate change and global warming. According to the availability of renewable energy sources in daily and seasonal patterns, the standalone power systems using renewable energy has difficulties in regulating the output power based on the load demand. The power generated from renewable energy sources becomes more reliable and affordable when it is combined with generated conventional power which will enable the hybrid system to produce sustainable targeted power supply. A schematic of a solar PV-Wind hybrid system is presented in
Different types of hybrid power systems namely wind/FC/UC-based hybrid power generation system, solar cell/wind turbine/fuel cell hybrid power system, and solar cell (SC), wind turbine (WT), fuel cell (FC) and ultra capacitor (UC) systems are modeled and simulated using SimPowerSystems and Matlab/Simulink software packages. The objective of these simulations is to achieve minimum or negligible fluctuation of power output from hybrid power system with respect to changes in load and environmental conditions. An integrated hybrid power system consisting of a photovoltaic energy system and a wind power system was modeled along with an optimized digital control system design and rapid Field Programmable Gate Array (FPGA) prototyping with the digital controller as shown in
i.e. SPV-Battery system, SPV-Fuel Cell (FC) system and SPV-FC-Battery system using HOMER software. The purpose of this simulation was to optimize, analyze and compare the effect of Maximum Power Point Tracker (MPPT) technology system on the three SPV systems using different storage technologies. It has been found from simulations that SPV-FC-Battery hybrid system has least system cost and best energy consumption pattern compared with the other two single storage systems. Sousa et al. have modeled and simulated systems of multiple sources of energy (SMSEs) using formalism Differential Hybrid Petri Nets. Petri Nets is used to describe large number of system models, analyze techniques and graphical representations considering local states and local actions with their mutual relationships. They modeled discrete events dynamic, continuous dynamics considering their mutual dependence and did formal verification.
A simulation model of combined biogas, bio-ethanol and protein fodder co-pro- duction in organic farming has been developed to analyze the scope of renewable energy production in sustainable agriculture. Site specific, load and resource dependent optimization of hybrid energy system, using MATLAB 12.0 software version, reveals that stability and continuous power supply property of hybrid energy system is better than any single renewable energy system. A renewable energy based hybrid (wind and solar) power system is modeled. The combined uncertainty in availability of energy, the load variation and compared the effects of different combinations of energy storage on load variation for adequate and reliable energy supply is also modeled. A simulation model was developed to optimize the system design of a hybrid power system with MATLAB software. Different types of hybrid generating systems with storage technology, namely photovoltaic system with diesel generator, wind power solar PV/hydrogen fuel cell energy system and the grid-connected hybrid generation system consisting of fuel-fired generators (FFGs), wind turbine generators (WTGs), PV panels (PVs), and storage batteries (SBs) are simulated by time-series based optimized simulation, MATLAB software and multi-objective particle swarm optimization algorithm coded language for design optimization, cost optimization considering system constraints and performance prediction.
The transient analysis of integrated generation systems (IGSs) due to sudden changes of load, parallel operation of rotating machines and static converters having different characteristics is simulated using a simulation package called Combined Multiple Renewable Energy Sources System Simulator (CMRESSS) to calculate the electrical and mechanical parameters during normal or abnormal conditions. This simulation package which runs in MS-DOS environment has been developed and tested by performing several simulations. A hybrid wind-dump load generation system under changing operating conditions and a wind-battery hybrid system is simulated and modeled by Takagi-Sugeno (TS) fuzzy model, linear quadratic regulator (LQR) and sliding mode nonlinear control design technique. The TS fuzzy based controller is compared with a proportional-integral (PI) controller and the simulation results show that the proposed controller provide less fluctuations in power output during wind speed and load variation disturbances than the PI controller in wind-hybrid power generation system. The results show (
Hybrid system. An operation and control methodology of a three phase, four wire voltage source inverter (VSI) under unbalanced voltage conditions for a hybrid power system is modeled. The control techniques are applied by dividing the supply voltages and currents into positive, negative and homo-polar sequence components which are controlled independently using different synchronously rotating reference frame systems. So the output voltage is unaffected by load imbalances. Windmill turbo simulated the effect of wind speed and tide variation on the output power of a grid connected wind/tidal hybrid system. They have simulated the system after incorporating a dynamic voltage regulator (DVR) controlled by a tri-loop dynamic error driven PI controller. Comparing the simulated results with that of the network without DVR, the power output and voltage variation is reduced. For instance, in isolated small islands, a standalone renewable energy based power supply system is simulated by fuel cell generators and wind turbine generators. The total output power meets the total load demand, no separate batteries are required and the system efficiency is improved. An object oriented simulation model using Any Logic simulation software has been developed to design micro grid hybrid system. Any Logic is a hybrid simulation software which integrates discrete event, system dynamics, and agent based models to model systems.
Using MATLAB (Version-12.0) software, the harmonic occurrence is analyzed. The computed value of the expressions in % for N number is shown in
The wind farm has a wind turbine unit. The unit consists a wind generator of 440 V rating. Using a step up transformer, the generated voltage of each wind turbine unit is stepped up to 440 V. Through a 1 km transmission line, the power from the step up transformer is transmitted to the grid. The proposed photovoltaic system is integrated with the wind energy system to form the hybrid system is shown in
The generated PWM from FPGA renders pulse to hybrid grid. The required power to the hybrid is generated from DC source. DC source consists of wind turbo and PV array. Relying to the wind speed, wind turbo is rotated and power is generated. Harmonics level is reduced in the generated power and it is converted from AC to DC. The generated DC is running through hybrid and is stored in the rechargeable battery. The PV array consists of eight PV panels. The generated power from eight PV panels is combined and boosted DC to DC and it is stored in the rechargeable battery. The stored power can be inverted and used in the load. The specified process has been contrived in the simulation.
Damodhar, T.S.B. and Kumar, Dr.A.S. (2016) Implementation of FPGA Based Hybrid Power Generator for PV and Wind Grid Applications. Circuits and Systems, 7, 4280-4290. http://dx.doi.org/10.4236/cs.2016.713350