In the recent earthquakes, concrete structures have been severely damaged or collapsed, which has raised questions against the seismic adequacy of existing buildings. These existing reinforced concrete buildings need to be evaluated to determine the capacity to resist seismic loads. The behavior of a building during earthquakes depends critically on its overall shape, size and geometry. Conventional approach to earthquake resistant design of buildings depends upon providing the building with strength, stiffness and inelastic deformation capacity which are great enough to withstand a given level of earthquake-generated force. This is generally accomplished through the selection of an appropriate building configuration and the careful detailing of structural members. In this research, nonlinear pushover analysis has been used to evaluate the seismic performance of three buildings with three different plans having same area and height. This method determines the base shear capacity of the building and performance level of each part of building under varying intensity of seismic force. The results of effects of different plan on seismic response of buildings have been presented in terms of displacement, base shear and plastic hinge pattern.
An earthquake is the vibration of the earth’s surface that follows a sudden release of energy in the crust. Ground surface moves in all directions during earthquake. The most devastating effects on buildings are caused by lateral movements which disturb the stability of the structure, leading to collapse sideways. Since buildings are normally constructed to resist gravity loads, many conventional systems of construction are not inherently resistant to horizontal forces. Strengthening of such buildings have been proved as more economical and viable immediate shelter solution rather than replacement of buildings [
These vulnerable buildings to damage need to be identified and an acceptable level of safety must be determined. To make such evaluation, pushover analysis which is a nonlinear method performance based method has been developed by structural engineers. Pushover analysis determines expected seismic performance of structural system by estimating its strength and deformation demands in design earthquake. Also this method determines the capacity curve for the building based on series of incremental static analysis. Based on this capacity curve, a targeted displacement (an estimation of design displacement during earthquake) is determined. In recent researches, capacity spectrum method (CSM), the displacement coefficient method (DCM) and modal pushover analysis (MPA) have been used to evaluate the performance of the buildings [
In modern world, challenges for structural engineer increased due to various types of irregularities involve in the buildings as designed by the architects. In more slendrical buildings, the horizontal movement of the floors increases significantly which may lead to increment in drift and overturning effects of the earthquake. Therefore, damaging effects are more in short but long buildings during earthquake shaking. Generally, seismic calculations are done by assuming ground as a solid elastic base under the building. This assumption is applicable in buildings with small plan area. However, chances for differential settlement of foundations in buildings with long plan increase due to uneven shaking of different parts [
In this paper, four buildings have been analysed with different plans of aspect ratio of 1, 1.5, 2 and 4 having the same area. The results are compared in terms base shear, displacement and plastic hinge pattern to evaluate the effects of different plan aspect ratio on the performance level of buildings. The study shows that hinges have developed in the beams and columns showing the three stages IO (immediate occupancy), LS (life safety) and CP (collapse prevention) as shown in
Static pushover analysis is an attempt by the structural engineers to evaluate the real strength of the structure and it promises to be a useful and effective tool for performance based design. In pushover analysis; building is subjected to incremental lateral loads at different levels representing the inertial forces due to ground shaking during earthquake. Consequently, at each increment some elements of structure may yield due to loss of stiffness as shown in
documents have developed modeling parameters, acceptance criteria and procedures of pushover analysis. Pushover analysis significantly evaluates the expected performance level of the structural system by the capacity curve of the building. Based on this capacity curve, target displacement is estimated which is expected to be produced during the earthquake. Also analysis enables to determine the collapse load and ductility capacity. The output of the analysis can better be explained by demand versus capacity curve. In
Four cases of residential building with plan aspect ratio of 1, 1.5, 2 and 4 are considered for study as shown in Figures 5-8. The buildings are composed of moment resisting RC frame with solid slab, 140 mm thickness, situated in zone 3. The structure members are made of in-situ reinforced concrete. The overall plan dimensions are 20 m × 20 m, 25 m × 16 m, 28.5 m × 14 m and 40 m × 10 m having same area of 400 m2. The buildings are five-story with height of 15.2 m. Columns and beams sizes are 500 × 300 mm and have been modelled as frame elements while in-plane rigidity of the slab is simulated using rigid diaphragm action. The columns are assumed to be fixed at the base. The building is analyzed as per seismic provisions provided by UBC-1997 [
The total design base shear according to UBC-1997 along any principal direction can be calculated by following equation [
The maximum total base shear will be taken as the following:
The minimum total base shear will be taken as the following:
The approximate fundamental period (T), in seconds, is determined from the following equation:
Dead Loads | |
---|---|
Water Proofing | 2.5 KN/m2 |
Super Imposed Load on Roof | 1 KN/m2 |
Floor Finish | 1 KN/m2 |
Partitions | 3 KN/m2 |
Live Loads | |
On Roof | 1 KN/m2 |
On Floors | 3 KN/m2 |
where:
V = total base shear.
W = total seismic weight of the building.
R = the response modification factor.
I = the occupancy importance factor.
hn = is the height in (m).
Ca and Cv are acceleration and velocity based seismic co-efficients respectively.
Ct = 0.035 (0.0853) for steel moment-resisting frames.
Ct = 0.030 (0.0731) for reinforced concrete moment-resisting frames and eccentrically braced frames.
Ct = 0.020 (0.0488) for all other buildings.
The base shear shall be distributed over the height of the structure, including Level n, according to the following formula:
where:
Ft = 0.07 T V < 0.25 V; when: T ≤ 0.7 sec.
Fx = the lateral seismic force at any level (KN).
All four buildings were analysed in both X and Y directions for static nonlinear (pushover) analysis using SAP2000. The Base shear versus displacement graphs have been plotted and compared for all models. The results show the highest values in X direction. Maximum base shear has been found in Case 4 (building with plan aspect ratio of 4). However, Case 2 shows the least value of base shear in both directions as shown in
It is the point where the capacity curve crosses the demand curve according to ATC-40 as shown in
Plastic hinge formation for all four buildings models have been obtained at different displacement levels. The hinging patterns are plotted in Figures 16-19. Comparison of these figures shows the quite similarity of hinging
pattern. Plastic hinge formation starts with the yielding of structural members of lower stories and then propagates to upper stories with yielding of intermediate columns. Case 2 shows the better performance of building in both directions with least number of hinges formed at performance point. However, Case 4 shows the most number of hinges at performance point as shown in Figures 20-22. Moreover, number of hinges formed at different levels of performance of building increases with increase in plan aspect ratio. Figures 20-22 shows the number of plastic hinges formed due to yielding of members, at different level of performance in X and Y directions. Also the analysis results showed the limited damage in four buildings due to yielding occurred at events B, IO and LS respectively.
Static pushover analysis is an attempt by the structural engineers to evaluate the real strength of the structure. This method of analysis promises to be a useful and effective tool for performance based design of structure. Four residential buildings with different plan aspect ratio have been analyzed by this method and results have been compared in terms of base shear, displacement and, plastic hinge pattern. From this study, following conclusions can be drawn.
1) Pushover analysis has been found relatively simple and evaluates the performance of the building close to more realistic behavior.
2) The plan dimensions significantly influence the seismic behavior of the buildings.
3) The building with plan aspect ratio 1.5 shows the least base shear in both directions, thereafter base shear significantly increases with increase in plan aspect ratio.
4) The inter story drift is relative displacement of one story relative to story below. It significantly increases in Case 3 and Case 4 with increase in plan aspect ratio.
5) Increasing plan aspect ratio makes the Y direction of building more vulnerable to damage during earthquake.
6) By increasing plan aspect ratio, the total number of hinges formed at different performance levels also increases, which may lead to building deficiency of resisting seismic loads.
7) Ductility is one of the most important factors affecting the building performance. Thus, earthquake-resistant design strives to determine the plan dimensions to ensure ductile behaviour of the building.
8) Finally, the architect and engineer should both employ ingenuity and imagination of their respective disciplines to reduce the effect of irregularities, or to achieve desired aesthetic qualities without compromising structural integrity.