Advances in Materials Physics and Chemistry
Vol.08 No.03(2018), Article ID:83552,13 pages
10.4236/ampc.2018.83010

Study of Nonradiative Recombination Centers in n-GaN Grown on LT-GaN and AlN Buffer Layer by Below-Gap Excitation

M. D. Haque1,2, M. Julkarnain3, A. Z. M. Touhidul Islam4, N. Kamata1

1Department of Functional Materials Science, Saitama University, Saitama, Japan

2Department of Electronics and Communication Engineering, Hajee Mohammad Danesh Science and Technology University, Dinajpur, Bangladesh

3Department of Applied Physics and Electronic Engineering, University of Rajshahi, Rajshahi, Bangladesh

4Department of Electrical and Electronic Engineering, University of Rajshahi, Rajshahi, Bangladesh

Copyright © 2018 by authors and Scientific Research Publishing Inc.

This work is licensed under the Creative Commons Attribution International License (CC BY 4.0).

http://creativecommons.org/licenses/by/4.0/

Received: February 26, 2018; Accepted: March 27, 2018; Published: March 30, 2018

ABSTRACT

Nonradiative recombination (NRR) centers in n-type GaN samples grown by MOCVD technique on a LT-GaN buffer layer and aAlN buffer layer have been studied by two wavelength excited photoluminescence (TWEPL). The near band-edge photoluminescence (PL) intensity decreases due to the superposition of below-gap excitation (BGE) light of energies 0.93, 1.17 and 1.27 eV over above-gap excitation (AGE) light of energy 4.66 eV. The decrease in PL intensity due to the addition of the BGE has been explained by a two levels recombination model based on SRH statistics. It indicates the presence of a pair of NRR centers in both samples, which are activated by the BGE. The degree of quenching in PL intensity for the sample grown on LT-GaN buffer layer is stronger than the sample grown on AlN buffer layer for all BGE sources. This result implies that the use of the AlN buffer layer is more effective for reducing the NRR centers in n-GaN layers than the LT-GaN buffer layer. The dependence of PL quenching on the AGE density, the BGE density and temperature has been also investigated. The NRR parameters have been quantitatively determined by solving rate equations and fitting the simulated results with the experimental data.

Keywords:

N-Type GaN, Two-Wavelength Excited Photoluminescence, Nonradiative Recombination Center, Recombination Model

1. Introduction

Gallium nitride (GaN) has been developed as a basis semiconductor for InGaN and AlGaN ternary compounds for such applications as green, blue, up to deep ultra-violet light emitters and high power electronic devices [1] . However, the full potential of GaN based devices has been restricted due to the lack of suitable substrate [2] . The sapphire substrates are generally used owing to low cost and high temperature stability [3] . But they introduce threading dislocations in a typical range of 109 - 1011 cm−2 due to lattice and thermal mismatch between epitaxial layer and substrate [4] [5] [6] . High density of these structural defects forms below-gap states in group III-V semiconductors (such as GaAs, InP and GaN) which act as non-radiative recombination (NRR) centers in the crystal and degrade the device efficiency and lifetime [7] [8] [9] . The insertion of buffer layer between substrates and epilayers has generated a lot of research interest for decreasing defect density in GaN based optoelectronics and microelectronics devices [10] [11] . It has been reported that the insertion of thin AlN buffer layer between GaN epilayer and sapphire substrate can reduce tensile growth stress and dislocation density which in turn improve crystalline quality compared to that of the LT-GaN buffer layer [12] [13] [14] [15] . Recently, the high temperature AlGaN MSFET with AlN buffer layer and better surface morphology and crystalline quality of thick AlGaN have been realized for the growth on the AlN buffer layer [16] [17] . However, for further improvement of GaN based device performance, it is still insufficient to understand the formation mechanism of defect states and structural optimization for eliminating them during the growth process. The GaN epilayers grown on LT-GaN buffer and AlN buffer layers has been characterized by photoluminescence (PL), scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies [11] [18] [19] [20] , but these methods give little information about NRR centers. Deep Level Transient Spectroscopy (DLTS) has been also used to study the deep levels in GaN epilayers [21] but its applications are restricted due to the necessity of preparing suitable sample for the measurements. On the other hand, our two-wavelength excited photoluminescence (TWEPL) is a versatile non-contacting and non-destructive scheme; no need to arrange any special kind of sample preparation. A comparative study of these types of samples has not been reported yet by this method.

In this work, TWEPL has been used for the detection and characterization of NRR centers in n-type GaN layers on a LT-GaN buffer layer and aAlN buffer layer grown on sapphire substrates. The change in PL peak intensity due to the addition of the BGE light over that of the AGE is observed as a function of AGE density, BGE density, and temperature. The NRR parameters have also been evaluated by systematically solving the rate equations and fitting the results with experimental data.

2. Experimental

2.1. Sample Structure

Two n-type GaN layers with Si concentration of 3 × 1016 cm−3 were grown on LT-GaN (sample A) and AlN buffer layer (Sample B), respectively, by metal organic chemical vapor deposition (MOCVD) method. The detailed structure of the samples is shown in Figure 1. The n-GaN (1.7 μm) layer was grown at 1050˚C after the sequence of LT-GaN (30 nm) or AlN (1.0 μm) buffer and i-GaN (3.0 mm) layer on c-plane (0001) sapphire substrate. All the layers except the buffer layer are same for both samples.

2.2. Measurement

The experimental setup for characterizing the n-GaN layers by TWEPL is shown in Figure 2. The sample was mounted in a temperature-controlled cryostat and

(a) Sample A (b) Sample B

Figure 1. Structure of n-type GaN samples; (a) sample A with LT-GaN buffer layer and (b) sample B with AlN buffer layer.

Figure 2. Experimental setup of the TWEPL measurement.

irradiated by diode-pumped solid-state (DPSS) laser of 4.66 eV (266 nm) as the AGE. The conventional PL spectra of both samples were measured at a temperature of 12 K. The output power of the AGE laser was kept constant at 16 mW and the neutral density filters were used for changing the excitation density. A temporally switched BGE light by an optical shutter with the internal 500 seconds ON/OFF was superposed on the AGE light to excite the sample at the same point. The BGE light of energy 1.27 eV (980 nm), 1.17 eV (1064 nm), and 0.93 eV (1340 nm) were used for the TWEPL measurement. The modulated PL signal from the sample was fed to a monochromator through a set of objective lenses, converted to photocurrent by a photomultiplier and recorded by a computer after the lock-in amplification. Here, an optical chopper was used with the digital lock-in-amplifier for improving the S/N ratio of the PL signal. By measuring PL intensity with and without the BGE, IAGE+BGE and IAGE, respectively, the normalized PL intensity IN = IAGE+BGE/IAGE was determined.

3. Results and Discussion

3.1. PL Intensity Comparison

The PL spectra of n-GaN samples measured at 12 K under the irradiation with the AGE light only are shown in Figure 3. Both spectra consist of near band-edge (NBE) luminescence (3.47 eV), shallow donor (oxygen) to valence band transition (Iox at 3.41 eV), donor acceptor pair (DAP) transition (3.27 eV), and yellow luminescence (YL) (2.3 eV) peaks. Same type of emission spectra has

Figure 3. PL spectra of n-GaN samples grown on LT-GaN buffer layer (Sample A) and AlN buffer layer (Sample B).

been also reported for GaN in earlier studies [2] . The NBE luminescence peak intensity of sample B is 8 times higher than that of sample A while the YL intensity of sample B is lower. The PL intensity is used to measure the quality of samples, and here it elucidates that quality of sample B is better than that of the sample A.

3.2. TWEPL Measurement

In this study, we focus on the NBE luminescence as the principal component for comparative analysis of two samples. The normalized PL intensity (IN) of the NBE peak has been measured at a fixed temperature of 12 K and the AGE density of 1.10 mW/mm2 is shown in Figure 4 as a function of the BGE power density for both samples.

With the addition of the BGE light, the value of IN quenches from unity for all BGE energies of 0.93, 1.17 and 1.27 eV. The quenching of the IN can be explained by two levels model schematically shown in Figure 5 indicating the presence of a pair of NRR centers in the sample whose energy difference correspond to that of the BGE energies [22] [23] [24] [25] . Determination of the NRR parameters becomes possible quantitatively by fitting experimental results based on Shockley-Read-Hall (SRH) statistics [22] [26] .

From Figure 4, it is observed that the amount of PL quenching becomes pronounced with increasing the BGE energy and density. It also exhibits that the value of IN for sample A is always lower than that of sample B throughout the

Figure 4. The normalized PL intensity (IN) of the NBE emission as a function of the BGE power density.

Figure 5. Two levels model of NRR process which explains the PL intensity quenching after irradiation of the BGE.

experimental BGE density range. The minimum values of IN, 0.60 and 0.74 are obtained for samples A and B, respectively at highest BGE density (1.37 W/mm2) of 1.17 eV BGE. The degree of change of the IN values from unity represents the density of NRR centers in the samples. Thus, this result implies that the density of NRR centers is higher in sample A compared to that in sample B. It is consistent with the relative intensity of conventional PL for these samples.

When the BGE energy matches the energy difference between two coexisting below-gap NRR levels, electrons in NRR level 1 are excited to NRR level 2 from which they recombine nonradiatively with holes in the valence band of GaN. Hence, the hole density in the valence band decreases. Similarly, the electron vacancies in the NRR level 1 allow an increase of NRR process from conduction band. Thus, the electron density in the conduction band decreases. The combination of both effects reduces the number of electron-hole pairs available for radiative recombination and resulting in the PL intensity quenching. In the region of low BGE densities, the electron occupation function of NRR level 2 remains much lower than 1 and the PL quenching proceeds with the increase in the BGE density. In the region of higher BGE densities, on the other hand, the electron occupation function of NRR level 2 approaches unity and the PL quenching shows saturation tendency with further increase in the BGE density.

The AGE density dependence of IN has been measured at a fixed BGE density and temperature by utilizing BGE energies of 0.93 and 1.17 eV shown in Figure 6. With increasing the AGE density from 1.10 mW/mm2 to 4.60 mW/mm2, the value of IN approaches to unity for both samples. At lower AGE density, the excitation of electrons via below gap states relative to band-to-band excitation

Figure 6. AGE power density dependence of the normalized PL intensity (IN) for samples A and B.

increases which results in higher BGE effect due to the enhancement of the non-radiative recombination. Similar AGE density dependence of the IN was observed in our previous studies of TWEPL [22] [25] [26] [27] .

The temperature dependence of IN for samples A and B has been also examined at a fixed AGE (1.10 mW/mm2) and BGE (1.37 W/mm2 and 0.95 W/mm2) densities shown in Figure 7. It has been observed that the IN value increases for both 1.17 and 0.93 eV BGE, with increasing temperature from 12 K to 70 K. The IN value of sample A enhances from 0.60 to 0.90, and that of sample B from 0.74 to 0.91, for 1.17 eV BGE. Further increase in temperature brings little change in the IN values, showing a saturating tendency up to 130 K. This type of temperature dependency was observed in previous studies and attributed to the thermal emission of electrons en from NRR level 2 to the conduction band in Figure 5 in the two levels model [28] [29] . This type of thermal emission reduces the electronic population in the NRR level 2 even under the below-gap excitation and decreases the BGE effect.

3.3. Rate Equation Analysis

In order to corroborate our qualitative interpretation by the two levels model, a semi-quantitative simulation for the TWEPL results of 1.17 eV BGE energy has been carried out. The rate equations of the two levels model as shown in Figure 5 can be written below with charge neutrality condition (CNC) [22] [30] [31] .

Figure 7. The Normalized PL intensity (IN) as a function of temperature observed for samples A and B.

d n d t = G 1 B n p C n 1 n N t 1 ( 1 f t 1 ) = 0 , d p d t = G 1 B n p C p 1 p N t 1 f t 1 C p 2 p N t 2 f t 2 = 0 , d f t 1 d t = C n 1 n N t 1 ( 1 f t 1 ) C p 1 p f t 1 G 2 f t 1 N t 2 ( 1 f t 2 ) = 0 , d f t 2 d t = G 2 f t 1 N t 2 ( 1 f t 2 ) C p 2 p N t 2 f t 2 = 0 , n + N t 1 f t 1 + N t 2 f t 2 = n 0 + p ,

where G1 [cm−3・s−1] and G2 [cm3・s−1] are generation rate for the AGE and the BGE, respectively, B [cm3・s−1] is the radiative recombination coefficient, Nt is the density of NRR levels, n0 is the density of free electrons, ft1 andft1 are the electron occupation function of NRR level 1 and NRR level 2, respectively.

For simplicity, we assumed that the electron capture coefficient Cn1 is equal to radiative recombination coefficient B, as 1.2 × 10−11 cm3・s−1 for GaN [32] . Such consideration has been taken by other researchers [26] [33] . Reshchikov et al. [1] [34] have reported that the hole capture coefficient of Cp1 is in the order of 10−6 cm3・s−1 for GaN. The hole capture coefficient of Cp2 has been also reported in the order of 10−9 cm3・s−1 [35] . The procedure of estimating generation rate of the AGE (G1) and BGE (G2) have been explained in our earlier study [30] .

The density of free electrons is assumed as n0 ≈ 1 × 1016 cm−3 for both samples considering the Si doping concentration. The system of rate equations can be solved numerically and the dependencies of n, p, ft1, and ft2 on G2 was found for the constant parameters of G1, B, n0, Nt, Cn, and Cp. By systematically solving and fitting the simulated results with experimental data, the defect parameters have been chosen as G1= 4.0 × 1020 cm−3・s−1, Cp1 = 1 × 10−6 cm3・s−1, Cn1 = 8.5 × 10−11 cm3・s−1 and Cp2 = 6.5 × 10−9 cm3・s−1 for both samples A and B, respectively. The densities of two NRR levels are obtained as Nt1 = 8.0 × 1015 cm−3, Nt2 = 3.0 × 1017 cm−3 for the sample A, and Nt1' = 6.1 × 1015 cm−3, Nt2' = 6.0 × 1016 cm−3 for the sample B. The value of IN is calculated as a function of generation rate of BGE (G2) under fixed AGE generation rate of 4.0 × 1020 cm−3・s−1 and shown in Figure 8. The broken and solid lines represent the simulated result together with experimental points for both samples. The simulated IN value shows a reasonable agreement with the measured points.

The dependence of the IN as a function of the electron-hole generation rate of the AGE (G1) at 12 K has been calculated by setting G2 = 1.0 × 10−14 cm3・s−1 and keeping all the other parameters as constant as previous. Figure 9 shows the IN value of the NBE peak for both samples as a function of the electron-hole generation rate of the AGE (G1).

Here, a set of parameters give the insight of below-gap states acting as NRR centers in samples A and B, and a reasonable fitting with experimental data. The estimated result shows that the densities of NRR centers are lower in sample B than that in sample A. From both fitting results, it is concluded that the interpretation based on the two-levels model is valid and the use of the AlN buffer layer is more effective for reducing the density of NRR centers in n-GaN layer than the LT-GaN buffer layer. The TWEPL study of NRR centers guides us to optimize growth conditions further.

Figure 8. Variation of the normalized PL intensity as a function of BGE density (G2). The broken and solid lines represent the simulated results for sample A and B, respectively.

Figure 9. AGE density (G1) dependence of the normalized PL intensity in samples A and B. The broken and solid lines represent the simulated results.

4. Conclusion

Defect States acting as NRR centers in n-type GaN layers grown on a LT-GaN buffer layer and aAlN buffer layer have been studied by TWEPL method. The near band-edge PL peak intensity quenches after the irradiation of BGE energies of 0.93, 1.17 and 1.27 eV. The quenching of the PL intensity has been interpreted by the two levels model and indicates the presence of a pair of NRR centers in the samples which are activated by the BGE. The dominant quenching of the PL intensity for the sample A (with LT-GaN buffer layer) indicates a direct evidence for the higher density of NRR centers compared to the sample B (with AlN buffer layer). A simulation of rate equations agreed well with our experimental data with a set of NRR parameters. The use of AlN buffer layer is more effective for reducing the NRR density in n-GaN layers than the LT-GaN buffer layer.

Cite this paper

Haque, M.D., Julkarnain, M., Islam, A.Z.M.T. and Kamata, N. (2018) Study of Nonradiative Recombination Centers in n-GaN Grown on LT-GaN and AlN Buffer Layer by Below-Gap Excitation. Advances in Materials Physics and Chemistry, 8, 143-155. https://doi.org/10.4236/ampc.2018.83010

References

  1. 1. Monemar, B. (1999) III-V Nitrides—Important Future Electronic Materials. Journal of Materials Science: Materials in Electronics, 10, 227-254. https://doi.org/10.1023/A:1008991414520

  2. 2. Reshchikov, M.A. and Morkoc, H. (2005) Luminescence Properties of Defects in GaN. Journal of Applied Physics, 97, 061301. https://doi.org/10.1063/1.1868059

  3. 3. Yu, H., Caliskan, D. and Ozybay, E. (2006) Growth of High Crystalline Quality Semi-Insulating GaN Layers for High Electron Mobility Transistor Applications. Journal of Applied Physics, 100, 033501. https://doi.org/10.1063/1.2221520

  4. 4. Lester, S.D., Ponce, F.A., Craford, M.G. and Steigerwald, D.A. (1995) High Dislocation Densities in High Efficiency GaN-Based Light-Emitting Diodes. Applied Physics Letter, 66, 1249-1251. https://doi.org/10.1063/1.113252

  5. 5. Weimann, N.G., Eastman, L.F., Doppalapudi, D., Ng, H.M. and Moustakas, T.D. (1998) Scattering of Electrons at Threading Dislocations in GaN. Journal of Applied Physics, 83, 3656-3659. https://doi.org/10.1063/1.366585

  6. 6. Cao, X.A., Teetsov, J.A., Sandvik, F.S. and Arthur, S.D. (2004) Microstructural Origin of Leakage Current in GaN/InGaN Light-Emitting Diodes. Journal of Crystal Growth, 264, 172-177. https://doi.org/10.1016/j.jcrysgro.2004.01.031

  7. 7. Guha, S., Depuydt, J.M., Haase, M.A., Qiu, J. and Cheng, H. (1993) Degradation of II-VI Base Blue-Green Light Emitters. Applied Physics Letter, 63, 3107-3109. https://doi.org/10.1063/1.110218

  8. 8. Sugahara, T., Sato, H., Hao, M., Naoi, Y., Kurai, S., Tottori, S., Yamashita, K., Nishino, K., Romano, L.T. and Sakai, S. (1998) Direct Evidence That Dislocations Are Nonradiative Recombination Centers in GaN. Japanese Journal of Applied Physics, 37, L398-L400.

  9. 9. Rosner, S.J., Carr, E.C., Ludowise, M.J., Girolami, G. and Erikson, H.I. (1997) Correlation of Cathodoluminescence Inhomogeneity with Microstructural Defects in Epitaxial GaN Grown by Metal Organic Chemical Vapor Deposition. Applied Physics Letter, 70, 420-422. https://doi.org/10.1063/1.118322

  10. 10. Yoshida, S., Misawa, S. and Gonda, S. (1983) Improvements on the Electrical and Luminescent Properties of Reactive Molecular Beam Epitaxially Grown GaN Films by Using AlN Coated Sapphire Substrates. Applied Physics Letter, 42, 427-429. https://doi.org/10.1063/1.93952

  11. 11. Kuznia, J.N., Khan, M.A., Olson, D.T., Kaplan, R. and Freitas, J. (1993) Influence of Buffer Layers on the Deposition of High Quality Single Crystal GaN over Sapphire Substrates. Journal of Applied Physics, 73, 4700-4702. https://doi.org/10.1063/1.354069

  12. 12. Coreki, S., Ozturk, M.K., Bengi, A., Cakmak, M., Ozcelik, S. and Ozbay, E. (2011) Charaterization of an AlN Buffer Layer and a Thick-GaN Layer Grown on Sapphire Substrate by Metal Organic Chemical Vapor Deposition (MOCVD). Journal of Material Science, 46, 1606-1612. https://doi.org/10.1007/s10853-010-4973-7

  13. 13. Amano, H., Sawaki, N., Akasaki, I. and Toyoda, Y. (1986) Metalorganic Vapor Phase Epitaxial Growth of High Quality GaN Film Using an AlN Buffer Layer. Applied Physics Letter, 48, 353-355. https://doi.org/10.1063/1.96549

  14. 14. Jeon, H.C., Lee, S.J., Kumar, S., Kang, T.W., Lee, N.H. and Kim, T.W. (2014) Effect of AlN Buffer Layers on the Structural and Optical Properties of GaNEpilayer Grown on Al2O3 Substrates by Using Plasma Assisted Molecular Beam Epitaxy. Journal of Korean Physical Society, 64, 1128-1131. https://doi.org/10.3938/jkps.64.1128

  15. 15. Amano, H., Iwaya, M., Kashima, T., Katsuragawa, M., Akasaki, I., Han, J., Hearne, S., Floro, J.A., Chason, E. and Figile, J. (1998) Stress and Defect Control in GaN Using Low Temperature Interlayers. Japanese Journal of Applied Physics, 37, L1540-L1542. https://doi.org/10.1143/JJAP.37.L1540

  16. 16. Muhtadi, S., Hwang, S., Coleman, A., Asif, F., Lunev, A., Chandrashekhar, M.V.S. and Khan, A. (2017) High Temperature Operation of n-AlGaN Channel Metal Semiconductor Field Effect Transistors on Low-Defect AlN Templates. Applied Physics Letters, 110, Article ID: 193501. https://doi.org/10.1063/1.4982656

  17. 17. Fleischmann, S., Richter, E., Mogilatenko, A., Weyers, M. and Tränkle, G. (2017) Influence of AlN Buffer Layer on Growth of AlGaN by HVPE. Physica Status Solidi (B), 254, Article ID: 1600696. https://doi.org/10.1002/pssb.201600696

  18. 18. Detchprohm, T., Yano, M., Sano, S., Nakamura, R., Mochiduki, S., Nakamura, T., Amano, H. and Akasaki, I. (2001) Heteroepitaxial Lateral Overgrowth of GaN on Periodically Grooved Substrates a New Approach for Growing Low-Dislocation-Density GaN Single Crystals. Japanese Journal of Applied Physics, 40, L16-L19. https://doi.org/10.1143/JJAP.40.L16

  19. 19. Yang, J.H., Kang, S.M., Dinh, D.V. and Yoon, D.H. (2009) Influence of AlN Buffer Layer Thickness and Deposition Methods on GaN Epitaxial Growth. Thin Solid Films, 517, 5057-506. https://doi.org/10.1016/j.tsf.2009.03.089

  20. 20. Wang, C.D., Yu, L.S., Lau, S.S., Yu, E.T., Kim, W., Botchkarev, A.E. and Morkoc, H. (1998) Deep Level Defects in n-Type GaN Grown by Molecular Beam Epitaxy. Applied Physics Letters, 72, 1211-1213. https://doi.org/10.1063/1.121016

  21. 21. Gotz, W., Johnson, N.M., Amano, H. and Akasaki, I. (1994) Deep Level Defects in n-Type GaN. Applied Physics Letters, 65, 463-465.

  22. 22. Kamata, N., Ocampo, J.M.Z., Hoshino, K., Yamada, K., Nishioka, M., Someya, T. and Arakawa, Y. (1999) Below-Gap Spectroscopy of Semiconductor Quantum Wells by Two Wavelength Excited Photoluminescence. Recent Research Development on Quantum Electronics, 1, 123-135.

  23. 23. Grimmeiss, H.G. and Monemar, B. (1973) Some Optical Properties of Cu in GaP. Physica Status Solidi (A), 19, 505-511. https://doi.org/10.1002/pssa.2210190214

  24. 24. Tajima, M. (1984) Fatigue and Recovery Effects of the 0.65-eV Emission Band in GaAs. Japanese Journal of Applied Physics, 23, L690-L693. https://doi.org/10.1143/JJAP.23.L690

  25. 25. Touhidul Islam, A.Z.M., Murakoshi, N., Fukuda, T., Hirayama, H. and Kamata, N. (2014) Optical Detection of Nonradiative Recombination Centers in AlGaN Quantum Wells for Deep UV Region. Physica Status Solidi (C), 11, 832-835. https://doi.org/10.1002/pssc.201300405

  26. 26. Julkarnain, M., Fukuda, T., Kamata, N. and Arakawa, Y. (2015) A Direct Evidence of Allocating Yellow Luminescence Band in Undoped GaN by Two-Wavelength Excited Photoluminescence. Applied Physics Letters, 107, Article ID: 212102. https://doi.org/10.1063/1.4936243

  27. 27. Ocampo, J.M.Z., Klausing, Z., Semchinova, H.O., Stemmer, J., Hirasawa, M., Kamata, N. and Yamada, K. (2001) Study of MBE-Grown GaN/AlGaN Quantum Well Structures by Two-Wavelength Excited Photoluminescence. Physica Status Solidi (A), 183, 189-195. https://doi.org/10.1002/1521-396X(200101)183:1<189::AID-PSSA189>3.0.CO;2-5

  28. 28. Kamata, N., Klausing, H., Fedler, F., Mistele, D., Aderhold, J., Semchinova, O.K., Graul, J., Someya, T. and Arakawa, Y. (2004) Effect of Modulation-Doping on Luminescence Properties of Plasma Assisted MBE-Grown GaN/AlGaN Quantum Well. European Physical Journal of Applied Physics, 27, 271-273.

  29. 29. Klausing, H., Kamata, N., Takahashi, F., Fedler, F., Mistele, D., Aderhold, J., Semchinova, O.K., Graul, J., Someya, T. and Arakawa, Y. (2003) Improved Quality of Plasma Assisted MBE-Grown GaN/AlGaN Quantum Wells Revealed by Two-Wavelength Excited Photoluminescence. Physica Status Solidi (C), 2658-2661. https://doi.org/10.1002/pssc.200303473

  30. 30. Shockley, W. and Read, W.T. (1952) Statistics of the Recombinations of Holes and Electrons. Physical Review, 87, 835-842. https://doi.org/10.1103/PhysRev.87.835

  31. 31. Hall, R.N. (1952) Electron-Hole Recombination in Germanium. Physical Review, 87, 387. https://doi.org/10.1103/PhysRev.87.387

  32. 32. Piprek, J. (2010) Efficiency Droop in Nitride-Based Light-Emitting Diodes. Physica Status Solidi (A), 207, 2217-2225. https://doi.org/10.1002/pssa.201026149

  33. 33. Grieshaber, W., Schubert, E.F., Goepfert, I.D., Karlicek, R.F., Schurman Jr., M.J. and Tran, C. (1996) Competition between Band Gap and Yellow Luminescence in GaN and Its Relevance for Optoelectronic Devices. Journal of Applied Physics, 80, 4615-4620. https://doi.org/10.1063/1.363443

  34. 34. Reschikov, M.A. and Korotkov, R.Y. (2001) Analysis of the Temperature and Excitation Intensity Dependencies of Photoluminescence in Undoped GaN Films. Physical Review B, 64, Article ID: 115205.

  35. 35. Kamata, N., Ocampo, J.M.Z., Okamoto, W., Hoshino, K., Someya, T., Arakawa, Y. and Yamada, K. (2002) Below-Gap Recombination Dynamics in GaN Revealed by Time-Resolved and Two-Wavelength Excited Photoluminescence. Materials Science and Engineering: B, 91-92, 290-293. https://doi.org/10.1016/S0921-5107(01)01032-7