Journal of Encapsulation and Adsorption Sciences
Vol.07 No.02(2017), Article ID:77240,13 pages

Methylene Blue and Brilliant Green Dyes Removal from Aqueous Solution Using Agricultural Wastes Activated Carbon

Ahmed Fate Ali1, Abdulsalami Sanni Kovo2, Sunday Adesola Adetunji2

1Department of Environmental Management, Bayero University Kano, Kano, Nigeria

2Department of Chemical Engineering, Federal University of Technology, Minna, Nigeria

Copyright © 2017 by authors and Scientific Research Publishing Inc.

This work is licensed under the Creative Commons Attribution International License (CC BY 4.0).

Received: January 30, 2017; Accepted: June 25, 2017; Published: June 28, 2017


This paper investigated the analyses of removal of Methylene Blue (MB) and Brilliant Green (BG) dyes from aqueous solutions by adsorption on activated carbon prepared by chemical activation of coconut shell, eucalyptus tree, corn cob and flamboyant pod. It was found that the carbon pores increased after carbonization and activation processes. The maximum percentage MB removal was obtained as 95.0% for coconut shell, 93.2% for eucalyptus tree, 99.9% for corn cob, and 99.7% for flamboyant pod. Also, the maximum percentage BG removal was obtained as 97.0% for coconut shell, 98.2% for eucalyptus tree, 99.6% for corn cob, and 99.6% for flamboyant pod. The adsorption isotherms of the adsorption process were studied, and Freundlich model showed the best fit with the equilibrium data. To optimize the operating conditions, the effects of contact time, adsorbent dosage, and pH were investigated by two levels of factorial experimental design method and adsorbent dosage was found as the most significant factor.


Adsorption, Activated Carbons, Acid Activation, Brilliant Green, Two-Level Factorial Design

1. Introduction

The release of dyes into wastewater from textile, cosmetic, paper and coloring industries poses serious environmental problems [1] . Dye availability in water, even if it is just small in quantity is unwanted and highly visible. Color prevents the proper entrance of sunlight into water bodies; it also retard photosynthesis; hinder the growth of aquatic biota and affect the solubility of gases within the water bodies. Dyes role in connection with several lungs, skin and many other respiratory problems have been reported globally [2] . Direct release of dyes containing wastewater into municipal environment can cause the production of poisonous carcinogenic products. The highest degrees of toxicity were discovered in direct and raw dyes [3] . Therefore, before wastewater is released into municipal environment, it is very important to reduce dye amount or concentration present in it. The commonly applied methods of treating wastewater are coagulation and flocculation, electrochemical treatment, liquid-liquid extraction, chemical oxidation and adsorption. Many methods have recently been used to remove both MB and BG from industrial effluents. Among these methods, adsorption is the most effective way for the removal of organic compounds from solution in term of its low cost of operation, ease of design, sensitivity to poisonous materials and simplicity of operation [1] . But its use is limited because of high cost and associated problems of regeneration, and this problem has initiated a constant and continuous search for cheaper alternatives. The search for the removal of organic pollutants using alternative low cost adsorbents is now on the rise by many researchers [4] . Wide varieties of high carbon content materials such as wood, coal, peat; nutshells, sawdust, bones, husk, petroleum coke and others have been utilized to produce activated carbon of varying efficiencies [5] . These materials, usually in irregular and bulky shapes, are always adjusted to exhibit the desired final shapes, roughness and hardness. Generally, the production of activated carbon involves pyrolysis or carbonization and activation as the two main production processes [6] . Numerous carbonaceous materials, particularly, those of agricultural base, are being investigated to possess potential as activated carbon. The suitable ones have minimum amount of organic material and a long storage life. Similarly they consist of hard structure to maintain their properties under usage conditions. They can be obtained at a low cost. Some of the materials that meet the above conditions have been used, in past works, to produce activated carbons which were subsequently used for the treatment of wastewater and adsorption of hazardous gases. Agricultural by-products like rice straw, soybean hull, sugarcane bagasse, peanut shell, pecan shell and walnut shells were used by V. Ponnusami et al., (2007) to produce Granulated Activated Carbons (GACs). The choice of a particular material for the production of effective adsorbent (activated carbon) is based on low cost, high carbon and low inorganic content. Agricultural materials have attracted the interest of researchers for the production of adsorbents because of their availability in large amount and at a low cost [7] . The selected materials employed in this study were coconut shell, corn cob, flamboyant pod and eucalyptus tree. Use of agricultural by-product for the production of activated carbon is primarily for economic and ecological advantages [8] . Commercial activated carbon used in surface and wastewater treatment is largely derived from coal. The advantages of coal-based carbons can be seen in their ability to remove toxic organic compounds from industrial and municipal wastewater as well as potable water. Another significant application of coal-based carbons is decolorization. The feedstock for these carbons, usually bituminous coal, is a non-renewable resource. The long-term availability of coal and its long-term environmental impact coupled with its potentially increasing cost has prompted researchers to consider renewable resources such as agricultural by-products as an alternative. Many efforts have been made to use low cost agro-waste materials in substitute for commercial activated carbon [9] . Some agro-waste materials studied for their capacity to remove dyes from aqueous solutions are coir pith, pine sawdust, tamarind fruit shell, bagasse, rice husk, orange peel, palm kernel shell, cashew nut shell, wallnut shell [10] . The present investigation is an attempt to remove Methylene Blue (MB) and Brilliant Green (BG) from synthetic wastewater by adsorption process using a low cost activated carbon prepared from agricultural wastes as an adsorbent. The coconut shell and corn cob are considered as agricultural wastes, therefore using them as raw materials for production of activated carbon is much more economical than the coal based activated carbon. In this study, the carbon adsorption method will be investigated for its efficiency in color removal from water bodies.

2. Materials and Methods

2.1. Carbonization

1 kg of each agricultural waste material (coconut shell, eucalyptus tree, corn cob and flamboyant pod) was charged into electric muffle furnace, which was then heated in the absence of oxygen at a temperature of 300˚C - 600˚C for one hour. The resulting charred materials were collected and cooled at room temperature.

2.2. Activation

Samples of all the carbonized material were weighed on electric weigh machine, soaked in one mole of phosphoric acid (H3PO4) 63% concentrated solution for 24 hours. The materials were then removed from the soaking after the 24 hours lapsed, and then washed with distilled water until leachable impurities due to free acid and adherent powder were removed and the pH of the water was 7. Finally, the samples were drained and dried in an oven at 80˚C for another 12 hours.

2.3. Preparation of Dye Solution

The accurately weighted (0.003 gram) of each MB and BG were dissolved in a distilled water to prepare dye mixture stock solution. 1000 mg/L stock solution of synthetic wastewater was prepared using blue and green dyes and from which other desired concentrations were obtained. The pH of the working solutions was adjusted to the required values of 4 and 11 by adding 0.1 M HCl.

2.4. Batch Adsorption Studies

For batch studies, the aim was to increase the dye adsorption efficiency during purification operation. To systematically explore process options, a full-factorial two-level design on the key factors was set up. Only three factors affecting dye adsorption efficiency were studied in this work, including contact time, dosage and pH. The symbols of minus (−) and plus (+) were used to designate low and high levels, respectively. Batch adsorption experiment was carried out in a set of 250 conical flasks containing 80 mL dye solution. The experiments were run according to 23 factorial design template designed for operation. The shaker speed was kept constant throughout the experiments run. After the completion of each experiment, the conical flask was withdrawn from the shaker at the pre-deter- mined time interval and the supernatant solution was separated by filtration using whatman filter paper. Standard calibration curve was developed at wavelength of 664 nm MB dye and 629 for BG dye. The final concentration was then analysed for absorbance by using Ultra-violet spectrophotometer with a blank solution as control. The percentage colour removal efficiency was calculated using:


where, Ci (mg/L) is the initial dye concentration, Cf (mg/L) final colour concentration.

The uptake of dye at equilibrium time was calculated from


where qe is the amount of adsorbed dye in mg/g. Co and Ce are the initial and equilibrium dye concentration in mg/L, V is the volume of the aqueous solution in ml and w is the mass of the adsorbent in g. Langmuir and Freundlich adsorption isotherm models were used to explain the sorption data obtained in this work.

3. Results and Discussion

3.1. Carbons Adsorption Comparison

The results as shown in Figure 1 and Figure 2 compare the dye adsorption during

Figure 1. MB removal efficiency.

batch experiments using activated and un-activated carbon. The graphs clearly show that activated carbon is better during adsorption process than un-activated carbon. It also shows that, all the activated carbons used during the experiments adsorbed dye from the dye solution more than all the un-activated carbons used for the experiments [11] . The graphs were plotted using the dye highest percentage removal in each experimental run for both activated and un-activated carbon. All the activated carbons used in the experiments have adsorption removal efficiency above 94.9% to 99.9% for both MB and BG. All the un-activated carbons have their highest between 72.5% to 76.3%. All the carbons flamboyant pod were activated using the same conditions of carbonization of 500˚C for 1 hour, and activation was done with 1 mole of 63% phosphoric acid and soaked for 24 hours.

3.2. Isotherm Models

Table 1 and Table 2 shows Freundlich and Langmuir coefficients and regression

Figure 2. BG removal efficiency.

Table 1. Freundlich data.

Table 2. Langmuir data.

correlation coefficients for adsorption of MB and BG dyes onto coconut shell carbon, eucalyptus carbon, corn cob carbon and flamboyant pod carbon at ambient temperature.

The initial dye concentration varied as 5, 10, 15, 20 and 25 mg/L, and four different adsorbent dosages of each 5 g was used for comparison. All constants and R2 values obtained for both models are summarized in Table 1 and Table 2. According to Table 1 and Table 2, the highest correlation coefficient (R2 values) were obtained from Freundlich equation; thus, the Freundlich model displayed better fit to the adsorption data than Langmuir model [12] . This result indicated that the surface of the produced carbons for adsorption of MB and BG were made up of heterogeneous adsorption patches [13] .

3.3. Two-Level Factorial Design of Experiments

Dye removal by an adsorbent in a batch experiments usually depends on many factors. These factors include contact time, adsorbate dosage, pH, and so forth. To systematically explore process options, a full-factorial two-level design on the key factors was set up as shown in Table 3.

Only three factors affecting dye adsorption efficiency were studied in this work, including contact time, adsorbent dosage and pH. The first factor, contact time is numerical because it can be adjusted to any level. Also, the second factor, dosage and the third factor, pH are also numerical. None of the factors used in this design is categorical, that is factor that cannot be adjusted. The experiments for two-level factorial design were carried out in a set of 250 ml conical flasks containing 80 ml MB and BG dyes solution of known pH, adsorbent dose and agitated for predetermined contact time. After thirty and ninety hours of agitation, the suspensions were filtered and dye concentrations in the supernatant solutions were measured using a UV-Vis spectrophotometer. The experimental design results were analysed using DESIGN EXPERT software to estimate the statistical parameters as well as effects, such as half-normal probability of the standardized effects, Pareto, interaction and main effects plots. 23 two-level factorial design with 8 runs experimentation for MB and BG removal was studied, and amatrix was developed according to their low and high levels, represented by −1 and +1, respectively. The coded values of variables with the responses (% removal efficiency) were illustrated in Table 4.

The interactions between independent variables were determined with ANOVA and the main effects of MB and BG adsorption were identified based on the P value with >95% of confidence level.

The codified equation below was used to explain the 23 factorial designs of MB and BG removal by four different activated carbons:

Table 3. Test factors for dye adsorption.


where Y is the predicted response, β0 is the intercept, βi is the regression coefficient related to the interactions and the main factors effects A is the contact time (mins), B is the adsorbent dosage (g), and C is the pH. The interaction and main effects, regression coefficients, coefficients of the model, standard deviation of each coefficient, standard errors, and T and P values were also done.

From Table 5 and Table 6, when the factor effect is negative, removal efficiency decreases as the factor is changed from low to high levels (as seen from dosage and pH). In contrast, if the effects are positive, removal efficiency increases for high level of the same factor (as seen from adsorbent dosage and pH). When the factor effect is negative, removal efficiency decreases as the factor is changed from low to high levels (as seen from pH and contact time). Furthermore, the fit models, submitted square correlation coefficient (R2) of 0.9992 for MB and 0.9939 for BG, were in good agreement with the statistical model. The factors A, B and C are the frequently called a main effect as it refers to the primary factor of interest in the experiment and factors AB, AC and BC are interactions effects. In this work, factors A, B, C AC, and BC are all significant effects. The AB and ABC effect were insignificant, when it was compared with other

Table 4. Design matrix for MB and BG.

Table 5. Interaction of dosage versus pH.

Table 6. Interaction of dosage versus pH.

effects. Thus the AB and ABC effects were neglected and did not included in the model equation. Then, model equation, related to the level of parameters and removal efficiency, was obtained by substituting the regression coefficients in for both MB and BG:



Equations (4) and (5) indicated that two-variable interactions were significant. Proof of positive (BC) and negative (AC) interactions was quite strong, thus, could not be ignored from the model. Although the main effects gave a clear idea, the interaction between those two parameters would favor a better statement of the process.

The interactions between independent factors were determined with analysis of variance (ANOVA) and the main effects of dye adsorption were identified based on the P value with >95% of confidence level are presented in ANOVA Table 7 and Table 8. The tables presented the possible positive and negative two-variable interactions among the variables A, B, and C for the removal efficiency (%).

Table 7. Statistical parameters and ANOVA for removal efficiency (%).

Table 8. Statistical parameters and ANOVA for removal efficiency (%).

It was observed that the effect of pH was more noticeable when the adsorbent dosage was high but at lower adsorbent dosage, effect of pH was not so high. On the contrary, pH effect and adsorbent dosage effect were high at higher contact time. The interaction effects are easily estimated and tested by using the ANOVA as shown in Figure 3. The ANOVA results of MB and BG were shown in Table 7 and Table 8 above. The sum of the squares used to estimate factors affect and Fisher’s F ratios (defined as the ratio of mean square effect and the mean square error) and P values (defined as the level of significance leading to the rejection of the null hypothesis) were also represented. Relative importance of the individual and interaction effects was given by the Pareto chart of the standardized effects in Figure 4. In order to identify whether the calculated effects were significantly different from zero, Student’s t-test was performed and horizontal columns in Pareto chart showed these values for each effect. The normal probability plot of the standardized effects with P = 0.05 to evaluate the significance of each factor and its interactions on removal efficiency (%) are presented in Figure 5. Half-Normal probability plot could be separated into two regions, the region on the right side has all the effects that were significant. For a

Figure 3. Interaction graph of dosage versus pH for MG and BG.

95% confidence level and seven degrees of freedom, Bonferroni limit was 11.7687 and t-value limit was 4.30265 for MB and BG adsorption. The minimum statistically significant effect magnitude for 95% confidence level is represented by the vertical line in the chart. Five values higher than 4.30265 (P = 0.05) were located at left of the dash line and were significant. It can be concluded that the adsorbent dosage was the strongest effect of the overall adsorption procedure for both MB and BG SCAC. The first (strongest effect), second, third, fourth and fifth important factor to the overall optimization of the batch adsorption process were arranged in sequential order in Pareto chart for both MB and BG. Factor B, A, C, AC and BC show the order of significant of each effect on MB adsorption

Figure 4. Pareto chart of effects for MB and BG adsorption.

Figure 5. Half-normal probability plot of the standardized effects for MB and BG at P = 0.05.

process. Similarly, factor B, C, A, BC and AC show the order of significance of each effect on BG adsorption process. The coefficient of AC interaction for both MB and BG adsorption had the negative value; thus, a decrease in contact time of the solution with a deduction of the pH caused an increase in removal efficiency (%). This antagonistic effect would not be distinguished in the univariate optimization of the dye removal process.

4. Conclusions

Carbon produced by chemical activation of carbonized coconut shell, eucalyptus tree, corn cob and flamboyant pod with an activation agent 63% H3PO4 were all capable of removing Methylene Blue and Brilliant Green dye molecules from aqueous solutions. The adsorption was favoured at Basic medium with pH value 11 and adsorption efficiency (%) was also found to increase with the increase in adsorbent dosage and contact time.

The equilibrium data were in good agreement with the Freundlich model. Additionally, the influence of pH (4 and 11), adsorbent dosage (2 g and 5 g) and contact time (30 mins and 90 mins) on removal efficiency (%) was designed by using 23 two level factorial design. It was examined by using analysis of variance (ANOVA), t-test, and Bonferroni ? test. According to Pareto Chart, half-normal, normal probability plot, main effects, interaction plots in variance analysis, the most significant factors on removal efficiency (%) were found to be adsorbent dosage (B), contact time (A), pH (C), the interaction between adsorbent dosage and pH (BC) and interaction between contact time and pH (AC), respectively.

Due to the obtained results, black carbons which are produced from chemical activation of carbonized coconut shell, eucalyptus tree, corn cob and flamboyant pod could be employed as an effective and low-cost adsorbent. Therefore, these successful adsorbents could be considered as an alternative to commercial activated carbons for the removal of reactive Methylene blue and brilliant green from aqueous solutions.

Cite this paper

Ali, A.F., Kovo, A.S. and Adetunji, S.A. (2017) Methylene Blue and Brilliant Green Dyes Removal from Aqueous Solution Using Agricultural Wastes Activated Carbon. Journal of Encapsulation and Adsorption Sciences, 7, 95-107.


  1. 1. ElQada, E.N., Allen, S.J. and Walker, G.M. (2008) Adsorption of Basic Dyes from Aqueous Solution onto Activated Carbons. Chemical Engineering Journal, 135, 174-184.

  2. 2. Cooper, P. (1993) Removing Colour from Dyehouse Wastewaters—A Critical Review of technology Available. Journal of the Society of Dyers and Colourists, 109, 97-100.

  3. 3. Jadhav, S.B., Phugare, S.S., Patil, P.S. and Jadhav, J.P. (2011) Biochemical Degradation Pathway of Textile Dye Remazol Red and Subsequent Toxicological Evaluation by Cytotoxicity, Genotoxicity and Oxidative Stress Studies. International Biodeterioration and Biodegradation, 65, 733-743.

  4. 4. Gupta, V.K., Gupta, B., Rastogi, A., Agarwal, S. and Nayak, A. (2011) A Comparative Investigation on Adsorption Performances of Mesoporous Activated Carbon Prepared from Waste Rubber Tire and Activated Carbon for a Hazardous Azo Dye—Acid Blue 113. Journal of Hazardous Materials, 186, 891-901.

  5. 5. Bonnamy, S. (1999) Carbonization of Various Precursors. Effect of Heating Rate. Part II. Transmission Electron Microscopy and Physicochemical Studies. Carbon, 37, 1707-1724.

  6. 6. Bourrat, X. (1997) Structure in Carbons and Carbon Artefacts. In: Marsh, H. and Rodriguez-Reinoso, F., Eds., Sciences of Carbon Materials, Universidad de Alicante, Secretariado de Publications, Spain, 1-97.

  7. 7. Marsh, H., Heintz, E.A. and Rodriguez-Reinoso, F., Eds. (1997) Introduction to Carbon Technologies. Universidad de Alicante, Secretariado de Publications, Spain, 669.

  8. 8. Marsh, H. and Rodriguez-Reinoso, F., Eds. (2000) Science of Carbon Materials. Universidad de Alicante, Secretariado de Publications, Spain, 673.

  9. 9. Marsh, H. (2001) Carbon Mesophase. In: Buschew, K.H, Cahn, J., Robert, W., Flemings Merten, C., IIscher, B., Kramer Edward, J., Subhash, M. and Patrick, V., Eds., Encyclopedia of Materials: Science and Technology, Elsevier Science Ltd., Amsterdam, 926-932.

  10. 10. Mattson, J.S. and Mark, H.B. (1971) Activated Carbon. Marcel Dekker Inc., New York, 237.

  11. 11. McGuire, M.J. and Suffet, I.H., Eds. (1980) Activated Carbon Adsorption of Organics from the Aqueous Phase, Vol. 1. Ann Arbor Science Publishers Inc., Michigan, 508.

  12. 12. McGuire, M.J. and Suffet, I.H., Eds. (1980) Activated Carbon Adsorption of Organics from the Aqueous Phase, Vol. 2. Ann Arbor Science Publishers Inc., Michigan, 589.

  13. 13. McGuire, M.J. and Suffet, I.H., Eds. (1983) Treatment of Water by Granular Activated Carbon, Advances in Chemistry Series, 202. American Chemical Society, Washington, 599.