Journal of Minerals & Materials Characterization & Engineering, Vol. 8, No.3, pp 189-201, 2009
jmmce.org Printed in the USA. All rights reserved
189
Effect of Buffer Solutions on the Flow and Fracture in Calcite
S.O.O. Olusunle*
1
, W.O. Siyanbola
2
, A.R. Adetunji
3
, M.O.Adeoye
3
and O.O. Adewoye
1
1. National Agency for Science and Engineering Infrastructure, NASENI, Abuja, Nigeria
2. Centre for Energy Research and Development, Obafemi Awolowo University, Ile-Ife, Nigeria
3. Materials Science and Engineering Dept., Obafemi Awolowo University, Ile-Ife, Nigeria
*e-mail: tolusunle@yahoo.co.uk
ABSTRACT
K
1
c Values that are environment – sensitive were obtained. Flow and fracture resulting from
Vickers indentation testing of {100} have been studied. Plastic flow occurred in calcite; they are
anisotropic and environment - sensitive. Fracture in calcite occurred in lateral, median, and
subsurface models. Meyer’s indices were determined and they also are environment – sensitive,
they were found to be n < 2.
KEYWORDS: Vickers indentation; flow and fracture; Meyer’s index; environment-sensitive;
anisotropy.
1. INTRODUCTION
Microindentation technique has been used by various authors to study near-surface deformation
behaviour of ceramic materials, using Vickers or Knoop indentor by applying low loads [1-4].
However, fracture toughness, often perceived as the limiting factor for ceramics applications, is
being improved to make ceramics competitive as engineering materials. It has been reported that
flaws that cause fracture of ceramic materials are smaller than 50µm in most cases [4].
Quenching temperature has been found to affect the microhardness of rhombohedral single
crystal when studies were carried out on freshly cleaved crystal surfaces of calcite [5].
190 S.O.O. Olusunle, W.O. Siyanbola, A.R. Adetunji, M.O.Adeoye and O.O. Adewoye Vol.8, No.3
Etch-pit morphology has also been studied on calcite cleavages by using different concentrations
of glacial acetic acid; where it is found that lateral reaction rates are less at high concentrations
as well as low concentrations of glacial acetic acid [6].
The aim of this work is to estimate K
1c
for calcite in the media (buffer solutions -
Na
2
HPO
4
/NaH
2
PO
4
) at room temperature; to investigate the anisotropy of microhardness (hence
K
1c
) in the media; to estimate the Meyer indices, and finally to study the flow and fracture as
they occur in calcite.
2. EXPERIMENTAL DETAILS
Calcite samples from Igbeti in south-western Nigeria, were annealed in a micro-furnace at 480
o
C
(753K) for 5 hours in air. This was undertaken to minimise error in the analysis of the material
due to intrinsic and extrinsic defects.
Vickers indentation experiments were undertaken in air and in the phosphate (Na
2
HPO
4
/Na
2
HPO
4
) buffer solutions, at room temperature.
The indentation load was varied in this order: 0.01N, 0.015N, 0.020N, 0.025N, 0.030N and
0.035N; average indent sizes were recorded for each load. In order to obtain self consistency
within a given experiment, the indentations were all made in one session using same indenter,
and the indents were evenly spaced approximately twice the length of the diagonal [7].
The solutions were applied on the surface of the samples, and then the indentations were made.
This was repeated for every indent.
Microhardness as a function of pH facilitates the investigation of the flow mobility or behaviour
as a function of pH values referred to as chemomechanical effect [8, 9, 10 & 11].
Load as a function of indent size relationship, given as
)1.....(................................................................................
n
adP =
,
(where 'a' is a materials constant, d is the indentation size and n is the Meyer’s index), reveals
whether the material's hardness increases with decrease in load (i.e. when n < 2), or that the
hardness is load-independent (i.e. n = 2), or that hardness number increases with increase in load
(i.e. n > 2). Grade II Gold (Au) was evaporated on the surface of the samples to enhance sharp
and clear photomicrographs.
Vol.8, No.3 Effect of Buffer Solutions on the Flow and Fracture in Calcite 191
3. RESULTS AND DISCUSSION
Microhardness numbers obtained from tests conducted on Beuhler Micromet microhardness
tester by using a standard Vickers Diamond indenter with axis aligned along <100> on the {100}
test surface can be presented as a Meyer’s plot for each environment, or alternatively represented
by equation (1) as shown above.
Vickers Hardness number decreased with increasing load (and indentation size) as is typical of
ceramic materials [12]. This variation is large in Calcite as reflected in Table 1. The variation in
SiC has been found to be 44.22MPa at 0.49N to 38.33MPa at 4.9N in air [13]; that of Beryl is
12.29MPa at 0.49N to 11.47MPa at 4.9N also in air [13].
Table 1. pH Dependence of K
1
c in Calcite.
Environment Air pH 6.5 pH 7.0 pH 7.5 pH 8.5 pH 8.8
P = ad
n
0.0642d
1.808
0.0722d
1.807
0.1496d
1.629
0.1405d
1.555
0.1183d
1.625
0.1226d
1.633
VHN (0.10N) 319GPa 53.5GPa 46.5GPa 49.9GPa 129.4GPa 62.4GPa
VHN (0.35N) 87.5GPa 30.3GPa 26.3GPa 31.0GPa 40.1Gpa 28.3Gpa
(E/H)
1/2
8.9086 8.3600 7.5101 9.0120 8.7382 8.4198
E(GPa) 54.11 54.11 54.11 54.11 54.11 54.11
H(GPa) 0.6818 0.7742 0.9593 0.6662 0.7086 0.7632
K
1
c(MPam
1/2
) 0.0217 0.0088 0.0067 0.0094 0.0126 0.0095
Flow and fracture patterns were observed and are environment sensitive. Pin-cushion indentation
as observed in Figures 1d and 1f is indicative of irreversible deformation in Calcite, which had
also been observed in Beryl tested in air [13].
It can now be deduced that (i) plastic flow occurs in calcite and is environment – sensitive and
(ii) plastic flow in calcite is anisotropic as well, suggesting the existence of a well defined slip
system, similar to the case of Beryl [13].
The above conclusion, emanating from the consequence of Sinking-in being associated with
anisotropic flow [14], has been observed to manifest in the characteristic and observed pin-
cushion effect [14,15] in Figures 1d and 1f.
Fracture in Calcite has occurred in the lateral and median model (Figures 1i, 1o and 1p), while
incidence of sub-surface cracking is observed in Figure 1a, for example. Fracture rarely
emanated from the indents except in Figures 1j and 1e, but there are instances of fracture activity
away from the indent (e.g. Figures 1a and 1p).
192 S.O.O. Olusunle, W.O. Siyanbola, A.R. Adetunji, M.O.Adeoye and O.O. Adewoye Vol.8, No.3
a b
c d
e f
Fig. 1 (a-p). Photomicrographs of cracks in Calcite. a. Calcite in Air under-10gm load:
Subsurface cracking (Sb): b. Calcite in PH 6.5 30gm load: Lateral Cracks stepped (Ls); c.
Calcite in PH 7.5 under 35gm load: Lateral cracks stepped (Ls); d. Calcite in PH 7.0 under
30gm load: Sinkin-in(S) and lateral cracks (L); e. Calcite in PH 8.8 under 15gm load;
Fracture (Fr); f. Calcite in PH 8.8 under 30gm load; Lateral cracks (L) and Sinkin–in(S);
Vol.8, No.3 Effect of Buffer Solutions on the Flow and Fracture in Calcite 193
g h
i j
k l
(Fig. 1, continued) g. Calcite in PH 8.5 under 20gm load; Peeling off effect due to
interaction of lateral cracks with change in PH (P); h. Calcite in PH 8.5 under 30gm load;
Lateral cracks (L); i. Calcite in PH 6.5 under 35gm load; Sinkin –in(S), Lateral cracks (L)
and medium cracks (M); j. Calcite in PH 7.0 under 25gm load; Lateral cracks stepped (Ls)
Parallel to test surface; k. Calcite in PH 7.0 under 30gm load; Fringes (Fri) that are
anisotropic, which denotes cleavage; l. Calcite in Air under 15gm load; Flow pattern;
194 S.O.O. Olusunle, W.O. Siyanbola, A.R. Adetunji, M.O.Adeoye and O.O. Adewoye Vol.8, No.3
m n
o p
(Fig. 1, continued) m. Calcite in PH 8.5 under 25gm load; Cleavage direction(C) parallel to
test surface n. Calcite in PH 8.8 under 35gm load; sinkin –in (S); o. Calcite in PH 8.8 under
30gm load; Lateral cracks (L) medium cracks (M), and Fringes (F); p. Calcite in Air under
30gm load; Medium cracks (M).
A plot of P Vs C
R3/2
is given in Figure 2 as a function of increasing load and environment. From
the relation
( )
)2......(..................................................)(
2/1
3/2
2/3
1
HECot
P
cK
R
r
R
C
Ψ=
ζ
Where ζ
rR
is a constant evaluated to be 0.032±0.002, C
R
is the radial crack length, the indenter
cone half angle, ψ = 74° for Vickers indenter, K
1
c is the stress intensity factor, (E/H) is the ratio
of Young’s modulus to hardness which is reflected in Table 1, and the value of E is 54.11 Gpa
[17].
Vol.8, No.3 Effect of Buffer Solutions on the Flow and Fracture in Calcite 195
Fig. 2. Applied load P against crack parameter C
R 3/2
as a function of environment.
Calcite was found to have maximum hardness at neutral pH, while minimum hardness was
observed at pH 7.5 (i.e. in basic medium), as shown in Figure 3. Further examination of
Calcite in 2-Propanol and in air revealed that there is a definite orientation dependence of
hardness in the former medium, denoting dislocation activity (Table 2, Figure 4), but the
dependence is less marked in air, in the trigonal Calcite.
196 S.O.O. Olusunle, W.O. Siyanbola, A.R. Adetunji, M.O.Adeoye and O.O. Adewoye Vol.8, No.3
0
20
40
60
80
100
120
pH 6.5pH 7.0pH 7.5pH 8.5pH 8.8
pH values
V icker's H ard ne ss N o.
0.098N
0.149N
0.196N
0.245N
0.294N
0.343N
Fig. 3. Dependence of Vickers Hardness number at specific load on pH.
Table 2. Orientation Hardness No. dependence of Calcite in air and in 2-propanol.
Calcite in Air Calcite in 2-Propanol
Orientation 0° 30° 60° Orientation 0° 30° 60°
X
-
(x10
-
4
m)
3.77 2.90 3.10 X
-3/2(x10-4m)
2.63 1.94 2.47
Crack length
X
(µm)
52.2 43.8 45.8 Crack length
X
(µm
41.0 33.5 39.4
Hardness
Number 10.21
14.43
13.26 Hardness
Number 16.55 24.79 17.92
Vol.8, No.3 Effect of Buffer Solutions on the Flow and Fracture in Calcite 197
0
5
10
15
20
25
30
030 60
Orientatio n(d eg.)
Vickers Hardness No.
Air
2-Propanol
Fig. 4. Orientation dependence of hardness no. of Calcite in Air and 2-propanol.
A notable mechanism for Rebinder effect, in which changes in surface charge influences near-
surface plastic deformation of surfaces and thereby the hardness, was observed in this study as
well [18].
This is as a result of some of the environments that facilitate flow in the near-surface region i.e.
softens it, and also reduced fracture strength, while others do not facilitate flow in the near
surface regions i.e. hardens it, and also increases the fracture strength.
At this point it is reasonable to suppose that a significant amount of plastic deformation
necessarily occurs in a “flow-zone” immediately around the indenter edge. Since material in this
198 S.O.O. Olusunle, W.O. Siyanbola, A.R. Adetunji, M.O.Adeoye and O.O. Adewoye Vol.8, No.3
zone cannot readily escape around the edge of the indenter, strain accumulates, rapidly
exhausting the limited work-hardening capacity of the material.
The environment-sensitivity of dislocation mobility in Calcite, an ionic solid, appears consistent
with the interpretation of the basic mechanism suggested earlier by Westwood et al [19]; electron
transfer during chemisorptions causes changes in the electronic structure and electrostatic
potential of the near surface region of the solid. In crystalline materials, this causes alterations in
the state of ionisation of near surface dislocation and point defects; consequently, the
electrostatic interactions between moving near-surface point defects and between dislocations,
and intrinsic and extrinsic point defects, and between dislocations and lattice, are changed. Since
these are the factors that control dislocation mobility (and hence hardness) in ionic materials, the
near surface of such crystals is environment-sensitive [16].
4. FRACTURE (MORPHOLOGY)
Cracking in all the environments on the test surface occurred for the entire load from 0.1N to
0.35N. The rectangular nature of the indents, denoting orientation dependence, suggests
cleavage rather than conchoidal fracture. Median cracks were observed in Figure 1p. Lateral
cracking stepped are seen in Figures 1b, 1c, and 1j.
The relation in equation (2) was plotted and a least square-fit analysis of results undertaken as it
can be observed in Figure 2. A linear plot was obtained for P-C
R3/2
thus confirming the universal
applicability of the relation in the estimation of K
1
c for crystals, as already reported for alumina
[15] SiC [16] and Beryl [13].
H in the (E/H) in equation (2) was obtained by taking the averages of Vickers indentation
diagonals “d” using the relations
)3....(................................................................................
2
2
α
P
H=
Where
d
2
1
=
α
An instance of peeling-off effect as a result of interaction of lateral cracks with environment is
seen in Figure 1g. Sinking-in was observed for PH 8.8 and 6.5.
Calcite has a hardness profile that is orientation dependent in 2- Propanol, this is shown in Figure
4. The dependence of Critical stress intensity factor K
1C
on pH is exhibited in a near sinusoidal
form, with a minimum value at pH 7, and peaks at pH 8.5; this is shown also in Figure 5.
Vol.8, No.3 Effect of Buffer Solutions on the Flow and Fracture in Calcite 199
Fig. 5. pH dependence of Critical Stress Intensity factor K
1C
in Calcite on {100}.
5.
CONCLUSION
K
1
c values are found to be environment – dependent and that flow and fracture occur in calcite.
Flow and fracture are anisotropic. The Vickers microhardness value demonstrates both
orientation and environment dependence. This work interestingly has implication for faceting,
polishing and other technological processes requiring surface and near surface materials
transport. This latter obviously forms the basis for further work.
0
0.002
0.004
0.006
0.008
0.01
0.012
0.014
66.5 77.5
8
8.5
9
pH
K
1C
200 S.O.O. Olusunle, W.O. Siyanbola, A.R. Adetunji, M.O.Adeoye and O.O. Adewoye Vol.8, No.3
REFERENCES
1. Pal T. And Kar T. ‘Studies of Microhardness anisotropy and Young’s modulus of
nonlinear optical crystal I-arginine hydrochlorobromo monohydrate” Materials Letters
59(11); 1400, 2005
2. Adeoye M.O. and Adewoye O.O. “Investigation of hardness anisotropy in tourmaline,
Journal of Minerals and Materials Characterization and Engireering, 3(2): 99, 2004
3. Adewoye O.O. and Agu J.I. “Knoop microhardness determination of the slip systems in
beryl [Be
3
Al
2
(SiO
3
)
6
]” Journal of Materials Sci. 6:953, 1987
4. J. A. Jacobs & T. F. Kilduff, Stress concentration and fracture toughness, Engineering
Materials Technology (2001), p 436 – 441, Prentice Hall, Inc.
5. J. R. Pandya et al Bulleting of materials science (India) Vol. 5 No. 1 (March 1983) p 79 –
82.
6. B. J. Mehta, Cryst. Res. and Technol. (Germany) Vol. 17, No. 8 (1982) p 939 – 942.
7. O. O. Adewoye, G. R. Sawyer, J. W. Edington and T. F. Page, European research, office
of the U. S. Army report no. DATA 37.74 –c- 1310 (1974)
8. Robert E. Cuthrell – The influence of hydrogen on the deformation and fracture of the
near surface region of solids: proposed origin of the Rebinder-Westwood effect, Journal
of Materials Science, Volume 14, Number 3 / March, 1979 612 – 618
9. S. V. Hainsworth and T. F. Page – Nanoindentation studies of the Chemomechanical
effect in sapphire, Journal of Materials Science, Volume 29, Number 21 / January, 1994,
5529-5540
10. S. J. Bull and T. F. Page – Chemomechanical effects in ion-implanted MgO,J. Phys. D:
Appl Phys. 22, 1989, 941-947
11. Honglin Zhu, Dale E. Niesz, Victor A. Greenhut, Robert Sabia – The effect of abrasive
hardness on the chemical – assisted polishing of (0001) plane sapphire
JMR.2005, Volume: 20:2, 504-520
12. B. R. Lawns, A. C. Evans and D. B. Marshall. J. Gmer. Ceram. Soc. 63 9-10 574 (1980)
13. O. O. Adewoye, J. Mater. Sci. Lett. 3(1984), p. 855-858
14. R. W. Armstrong and C. Wu, J. Am Ceram. Soc. 61, Nos. 3- 4 pp. 102-106 (1978)
15. S. S. Smith and B. J. Plekta, Indentation fracture of Single Crystals and Polycrystalline
Alumina (1983) p 189 (Plenum Press, New York ed. RC Bradt A.G. Evans, D.P.H.
HAsselman and F.F. Large)
16. O. O. Adewoye, in Fracture Mechanics of Ceramics edited by R.C. Bradt A. G. Evans,
D.P.H. Hasselman and F. F. Large , Plenum Press New York (1983) p 107
17. George V. Chilinger, Harold J. Bissell, Rhodes W. Fairbridge Eds., Development in
Sedimentology 9B, Carbonate Rocks, Physical & Chemical spects, p.362-3
18. Alley David W, Devereux Owen F. Coolant pH of optimum Ceramic griding .I. Rebinder
effect in polycrystalline aluminum oxide, Journal of Materials Sc. (J. mater.Sci.)(2002),
vol.37no23, p 5135-5140
Vol.8, No.3 Effect of Buffer Solutions on the Flow and Fracture in Calcite 201
19. A.R.C. Westwood et al, Relationship between Zeta Potential and dislocation mobility
(1973), Martin Marietta Lab., Baltimore, Maryland 21227 USA