Journal of Geoscience and Environment Protection
Vol.06 No.12(2018), Article ID:89395,13 pages
10.4236/gep.2018.612010

Geotechnical Investigations and Estimation of Earthquakes Factors at an Industrial Qift City, Qena, Egypt

Hesham A. H. Ismaiel

Geology Department, Faculty of Science, South Valley University, Qena, Egypt

Copyright © 2018 by author and Scientific Research Publishing Inc.

This work is licensed under the Creative Commons Attribution International License (CC BY 4.0).

http://creativecommons.org/licenses/by/4.0/

Received: August 9, 2018; Accepted: December 22, 2018; Published: December 25, 2018

ABSTRACT

The present work dealt with the estimation of geotechnical parameters and earthquakes factors of poultry feed factory project constructing at an industrial Qift city, Qena, Egypt. The geotechnical parameters were including gradation parameters, shear velocity (Vs), shear parameters (frictional angle and cohesion), and allowable bearing capacity. The earthquakes factors were including soil coefficient (S), limits of constant value for elastic response spectrum (TB and TC), and specified value for begin of the constant displacement spectrum (TD). The present study was interested also in an estimation of design ground acceleration (ag). To achieve these objectives, five mechanical wash boreholes were conducted at ten meter depth. Fifty disturbed samples were collected. Geotechnical laboratory tests were carried out like grain size analyses, direct shear box, and shear velocity (Vs). Standard penetration test (SPT) as geotechnical field test was conducted. The results showed that the studied soils were classified as well graded and poorly graded sands (SP and SW) according to the unified soil classification system (USCS). The earthquakes factors including S, TB, TC, and TD were 1.80, 0.10, 0.30, and 1.20 respectively. The ag-value of the studied area was 0.10. According to Egyptian code for vibration and dynamic load foundations, the studied project area was classified as low potential seismic. According to Egyptian code for shallow foundation, the allowable bearing capacity of the studied sands ranging from 1.5 to 3 kg/cm2 at shallow foundation width must be not less than one meter. Shallow foundations like isolated footing or structural mat were recommended.

Keywords:

Earthquakes Factors, Standard Penetration Test, Shear Velocity

1. Introduction

Industrial Qift city is one of the new industrial cities in Qena governorate; it was constructed to collect all the industrial activates in Qena region to encourage the investment and to contribute in the development of Qena city (Figure 1 & Figure 2). The local geological conditions and shallow shear wave velocity structure of a site have a significant effect on earthquake ground motion. This effect is known as the site effect and may cause amplification of earthquake ground motion in frequency ranges unfavorable for buildings and structures especially in the presence of soft sedimentary covers overlying the bedrock ( Mostafa et al., 2016

Figure 1. Location map of the studied area, modified after ( Ismaiel , 2013).

Figure 2. Land sate image of the studied project.

Figure 3. Layout of the studied project illustrated the boreholes (B1 to B5) distribution and the corner points (A, B, C, and D).

1.1. Previous Works

Little of earthquakes assessment and geological hazards researches were conducted on the studied area by (Mostafa et al., 2016), (Sawires et al., 2016), and (Deif et al., 2011). The studied area was geologically investigated by many of authors. Sedimentlogical and stratigraphical investigations were conducted by (Sabry, 1968), (Said & Sabry, 1964), (Krasheninnikov & Penikarvo, 1964), (Hermina & Issawi, 1969), (Philiobbos, 1969), (Issawi, 1972), (Issawi et al., 1978), and (Abd El-Rahman, 1980). Structural and tectonics studies were carried out by (Said, 1962), (Abd El-Razik & Razvaliaev, 1972), and (Abdalla et al., 1977). Geomorphological and geomorphological hazards works were achieved by (Said, 1971), (Youssef et al., 2009), and (El-Etr et al., 1979). Surveying works were done by (Makhloof et al., 2013). Engineering geophysical researches were conducted by (Ismail, 2000), and (Basher, 2003). Few geotechnical studies were carried out by (Wuest & McLane, 2000), (Ismaiel et al., 2011), (Ismaiel et al., 2012), and (Ismaiel, 2013).

1.2. Scopes of the Present Work

The present study deals with the estimation of the geotechnical parameters of the studied soils including gradation parameters, shear parameters (ϕ & Cu), and shear velocity (Vs) to calculate the earthquakes factors of the studied soils and the design ground acceleration (ag). That helps in determination of the seismic suitability of the studied area for constructing the poultry feed factory at an industrial Qift city. It also deals with calculation the allowable bearing capacity of the studied soils. The earthquakes factors are including soil coefficient (S), limits of constant value for elastic response spectrum (TB and TC), and specified value for begin of the constant displacement spectrum (TD). These earthquakes factors help the civil engineer to calculate the total base shear due to earthquakes (if happened) to design the project foundations to avoid the possible seismic damages.

1.3. Geological Setting

The investigated area is located at the east of Qift city, 20 km south of Qena city. The coordinates of the studied area illustrated in Table 1. The area has a wide variety of sediments belonging to the Upper Cretaceous-Lower Tertiary succession as well as the Pliocene-Recent sediments (Ismail, 2000). It is covered by Quaternary sediments in the form of Nile silt, Wadi deposits, and pre-Nile sediments. The studied soils are representative of pre-Nile sands named Qena Sand Formation (Pleistocene age). The area is surrounded by Pliocene deposits and Dawi Formation at both east and southeast directions. The distribution of the studied Quaternary sediments is showed in Figure 4. The studied area is located in a transitional zone between the eastern desert and the Nile valley. It is characterized by a simple topography follows the regional northwest slope towards the Nile. The area around the industrial Qift city is dissected by many large wadies like Wadi Matuli to the east and Wadi Khozam to the south. The courses of these wadis are running from the southeast to the northwest direction depending on the direction of dominant fault strikes and that pointed sure to that these wadis have structurally controlled origin. The study area is located at the recently stable tectonic zone.

2. Materials and Methods

2.1. Materials

Fifty disturbed samples were collected from five (B1 to B5) wash mechanical drilling boreholes (10 m depth); one sample was selected in each one meter

Table 1. The coordinates of the studied area. (A, B, C, and D (corners points of the studied area)).

Figure 4. Geological map of the studied area modified after (Egyptian Geological Survey and Minning Authority, 1978).

depth (Figure 2 & Figure 3 & Figure 5). The studied soils were belonging to the pre-Nile sediments named Qena Sand Formation and having Quaternary age.

2.2. Methods

Subsurface exploration wash mechanical drilling according to (Egyptian Code, Part 2, 2001) was carried out to achieve five (B1 to B5) boreholes (10 m depth) and to collect the studied specimens (Figure 6). One geotechnical test in the field during the drilling process named standard penetration test (SPT) was conducted according to (Egyptian Code, Part 2, 2001) to calculate the frictional angle (ϕ) and the cohesion (Cu) of the studied sand samples. Three geotechnical tests in the laboratory including grain size analysis, direct shear box (Egyptian Code, Part 2, 2001), and shear velocity (Vs) using JAMES instrument (Yesiller et al., 2001) were conducted on the studied sand samples to measure the shear parameters and the shear velocity values which help to determine the soil class (Egyptian Code, Part 6, 2001).

3. Results

3.1. Wash Mechanical Drilling Results

Correlation between three boreholes data (B2, B3, and B4) was carried out to create a vertical cross-section of the studied area in XY-direction (Figure 2). The lithology of B1 and B2 was similar to B3.The results showed that the area composed mainly of sands. From the surface to one to two meter depth, the soils composed of poorly graded sands, and from two meter depth to ten meter depth composed of well graded sands (Figure 5). There was no underground water until the end of drilling depth (10 meter) of the studied boreholes. The sands samples at the studied cross-section were dry that means the pore water pressure

Figure 5. Cross-section in the studied area along the XY-direction.

Figure 6. Standard penetration test (SPT) during wash mechanical drilling.

of the studied sands equal to zero.

3.2. Grain Size Analyses Results

Figure 7 showed the grain size distribution curves of the studied sand samples. The studied sand samples composed mainly of sand size ranging from 92% to 95% and trace of silt size ranging from 2% to 5% as well as trace of fine gravels ranging from 3% to 5%. The results of the grain size distribution test of the studied soils showed that the sand samples at the five studied boreholes were classified as poorly graded sands (SP) at the first two meters depth where the gradation parameters of the studied sands including coefficient of uniformity were less than 6 according to unified soil classification system (USCS). But the sands collected from two meter to ten meter depth were classified as well graded sands (SW) where the gradation parameters of the studied sands including coefficient of uniformity were more than 6 according to USCS.

3.3. Shear Wave Velocity (Vs) Results

The results pointed to that the shear wave velocities (Vs) of the studied sand samples compacted at the maximum modified proctor density were ranging from 155 to 176 m/s.

3.4. Direct Shear Box Results

The direct shear box test was carried out to determine the frictional angle (ϕ)

Figure 7. Grain size distribution curves of the studies sand samples.

and the cohesion (Cu) of the collected soil samples (in the laboratory).

Three representatives and samples were collected from borehole no. 2, 3, and 4 and tested according to (Egyptian Code, Part 2, 2001). The results were listed below in Table 2. The results showed that the friction angle values of the studied sandy soils ranging from 32˚ to 40˚. The frictional angels of the sand at B2, B3, and B4 were 32˚, 35˚, and 40˚ respectively. The results illustrated that the cohesion values (Cu) of the studied sandy soils equal to zero.

3.5. Standard Penetration Test (SPT) Results

Standard penetration tests (SPT) were conducted (in the field), associated with the wash mechanical drilling process, on the studied sands beds according to (Egyptian Code, Part 2, 2001) using blow weight equal to 62.5 kg and drop height equal to 76 cm, the blow numbers (Nspt) recorded each 30 cm penetration. SPT-values were ranged from 9 to more than 45 blow number each 30 cm penetration. Generally the surface loose poorly graded sands (at the first two meters depth) have the lowest values ranging from 9 to 10. SPT-values were increased with increasing the depth and the compaction of the sands. The greatest values were ranging from 30 to 45 at about 8 to 10 meters depth and described as dense sands. Some intermediate SPT-values were ranging from 10 to 30 and described as medium dense sands (at depth ranging from 3 to 7 meters). The relationship between the SPT-values, the relative density, and the frictional angle of the soils according to the Egyptian code showed in Table 3.

4. Estimation of Earthquakes Factors

Earthquakes factors were estimated according to (Egyptian Code, Part 6, 2001). There are six activity zones in Egypt arranged from the first zone to the fifth B

Table 2. Frictional angle (ϕ) and cohesion values (Cu) of the studied sand samples.

Table 3. The relationship between the SPT-values, the relative density, and the frictional angle of the soils after (Egyptian Code, Part 2, 2001).

zone. The study area at Qena city is located in the first seismic zone (zone no. 1) (Figure 8 & Table 4). The value of design ground acceleration (ag) at seismic zone no. 1 was 0.10 g (Table 5). The geotechnical tests results showed that the soil layer type of the study area was class D, where the number of blow each 30

Figure 8. Seismic activity zones in Egypt, after (Egyptian Code, Part 6, 2001).

Table 4. Seismic effect zones for cities in Egypt (Egyptian Code, Part 6, 2001).

cm was less than 15 (ranging from 9 to 10) at the first two meter depth according (Egyptian Code, Part 2, 2001) (where the minimum drill depth of the shallow foundations must not be less than 0.8 m) and the cohesion values of the sand soil was less than 70 KN/m2 (equal to zero) as well as Vs-values were less than 180 m/s (ranging from 155 to 176 m/s), see Table 6. Based on the determined soil layer type (class D), the earthquakes factors including S, TB, TC, and TD were 1.80, 0.10, 0.30, and 1.20 respectively (Table 7). According to Egyptian code for vibration and dynamic load foundations, the studied project area was classified as low potential seismic.

Table 5. Values of design ground acceleration (ag) and seismic zones (Egyptian Code, Part 6, 2001).

Table 6. Soil layers classification under foundations (Egyptian Code, Part 6, 2001).

Table 7. Earthquakes factors based on subsoil class (Egyptian Code, Part 6, 2001).

5. Estimation of Allowable Bearing Capacity of the Study Soils

According to the Egyptian code of shallow foundations, (in case of dry soil where pore water pressure equal to zero as in the present study area) allowable bearing capacity of the studied medium to dense sand at the designed drill depth of the shallow foundations (not less than 0.8 m depth) was ranging from 1.5 to 3 kg/cm2 (at shallow foundation wide must not be less than 1 m). Table 8 showed the allowable bearing capacity according to (Egyptian Code, Part 3, 2001) in dry conditions for the soils.

6. Conclusions and Recommendations

6.1. Conclusions

The studied soils are representative of pre-Nile sands named Qena Sand Formation (Pleistocene age). The scope of the present work was the estimation of the geotechnical parameters of the studied soils including gradation parameters, shear wave velocities, and shear parameters to determine the earthquakes factors, the design ground acceleration, and the allowable bearing capacity of the studied soils. The estimation of earthquakes factors of the studied soils was to determine the seismic suitability of the studied area to construct poultry feed factory at the industrial Qift city, Qena, Egypt. The earthquakes factors are including soil coefficient (S), limits of constant value for elastic response spectrum (TB and TC), and specified value for begin of the constant displacement spectrum (TD). These earthquakes factors help the civil engineer to calculate the total base shear due to earthquakes (if happened) to design the project foundations and to avoid the possible seismic damages. To achieve these objectives, fifty disturbed samples were collected from five wash mechanical drilling boreholes (10 m depth). Grain size analyses, shear wave velocity, direct shear box, and standard penetration tests were carried out on the studied sand samples.

The results of the grain size analysis test of the studied soils showed that the sands samples at the five studied boreholes were classified as poorly graded

Table 8. Allowable bearing capacity values according to (Egyptian Code, Part 3, 2001).

sands (SP) at the first two meters depth where the gradation parameters of the studied sands including coefficient of uniformity were less than 6 according to USCS. But the sands collected from two meter to ten meter depth were classified as well graded sands (SW) where the gradation parameters of the studied sands including coefficient of uniformity were more than 6 according to USCS. SPT-test results pointed to that the surface loose poorly graded sands (at the first two meters depth) have the lowest values ranging from 9 to 10. SPT-values were increased with increasing the depth and the compaction of the sands. The greatest values were ranging from 30 to 45 at about 8 to 10 meters depth and described as dense sands. Some intermediate SPT-values were ranging from 10 to 30 and described as medium dense sands (at depth ranging from 3 to 7 meters). The results of the shear wave velocity tests illustrated that Vs-values were ranging from 155 to 176 m/s.

The results of direct shear box tests showed that the friction angle values of the studied sandy soils range from 32˚ to 40˚. The frictional angels of the sand at B2, B3, and B4 were 32˚, 35˚, and 40˚ respectively. The results showed also that the cohesion values (Cu) of the studied sandy soils equal to zero. According to Egyptian code for vibration and dynamic load foundations, the studied area is located in the first seismic zone (zone no. 1). The ag-value is 0.10 and the earthquakes factors including S, TB, TC, and TD were 1.80, 0.10, 0.30, and 1.20 respectively that means the studied project area was classified as low potential seismic, so that the potential for liquefaction of the soils at the study area is negligible during seismic shaking (if happened). According to the Egyptian code of shallow foundations, (in case of dry soil and the pore water pressure equal to zero as in the present study area) the allowable bearing capacity of the studied sand medium to dense at the designed drill depth of the shallow foundations (not less than 0.8 m depth) was ranging from 1.5 to 3 kg/cm2.

6.2. Recommendations

1) Shallow foundations either isolated footing or structural mat are recommended. According to the Egyptian code for shallow foundations, it is recommended that, the minimum drill depth of the shallow foundations must not be less than 0.8 m.

2) Compaction of the studied sands is recommended to obtain at least eighty seven percent of the maximum modified proctor density value.

Acknowledgements

Greatly thanks to the owner of the poultry feed factory project for valuable cooperation.

Conflicts of Interest

The author declares no conflicts of interest regarding the publication of this paper.

References

  1. 1. Abd El-Rahman, M. A. (1980). Geology of the Area Southeast of Qena with Special Reference to Phosphate Deposits. M.Sc. Thesis, Assiut: Assiut University.

  2. 2. Abd El-Razik, T. M., & Razvaliaev, A. V. (1972). On the Tectonic Origin of the Nile Valley between Idfu and Qena. Egyptian Journal of Geology, 2, 235-244.

  3. 3. Abdalla, A. M., Abu-Khadrah, A. M., & Abd El-Razik, T. M. (1977). New Light on the Geologic Structure of East Qena Region, Upper Egypt. In Proceeding of the VI Colloquim on the Geology of the African Region (pp. 767-778). Athens, II.

  4. 4. Basher, A. A. (2003). Application of Geophysical Techniques at New Qena City, Qena, Egypt. M.Sc. Thesis, Qena: South Valley University.

  5. 5. Deif, A., Hamed, H., Igrahim, H. A., Abou Elenean, K., & El-Amin, E. M. (2011). Seismic Hazard Assessment in Aswan, Egypt. Journal of Geophysics and Engineering, 8, 531-548. https://doi.org/10.1088/1742-2132/8/4/006

  6. 6. Egyptian Code (2001) Egyptian Code of Soil Mechanics, Foundations Carrying Out and Designation, Part 2 (6th ed.). Laboratory Tests. [Paper reference 27]

  7. 7. Egyptian Code (2001) Egyptian Code of Soil Mechanics, Foundations Carrying Out and Designation, Part 6 (6th ed.). Vibration and Dynamic Load Foundations. [Paper reference 220]

  8. 8. Egyptian Code (2001) Egyptian Code of Soil Mechanics, Foundations Carrying Out and Designation, Part 3 (6th ed.). Shallow Foundations. [Paper reference 47]

  9. 9. Egyptian Geological Survey & Minning Authority (1978). Geological Map of Qena Quadrangle, Egypt, Scale 1:500,000. [Paper reference 1]

  10. 10. El-Etr, H. A., Yousif, M. S. M., & Dardir, A. A. (1979). Untilization of (Landsat) Images and Conventional Aerial Photographs in the Delineation of Some Aspects of Geology of Central Eastern Desert, Egypt. Annals of the Geological Survey of Egypt, IX, 136-162.

  11. 11. Hermina, M. H., & Issawi, B. (1969). Rock Stratigraphic Classification of Upper Cretaceous-Lower Tertiary Exposures in Southern Egypt. Symposium on the Geology of Libya, University of Tripoli, 147-154.

  12. 12. Ismaiel, H. A. H. (2013). Cement Kiln Dust Chemical Stabilization of Nile Silt Soil Exposed Along Nile Banks at Taramsa Village, Qena Region, Egypt. International Journal of Scientific & Engineering Research, 4, 1428-1437. [Paper reference 12]

  13. 13. Ismaiel, H. A. H., Askalany, M. M., & Badry, M. M. (2011). Geotechnical Propertied and Classification of Both Non-Expansive and Expansive Soils Exposed along the New Upper Egypt-Red Sea Road, Eastern Desert, Egypt. Scientific Journal of Banha University, 6, 1-18.

  14. 14. Ismaiel, H. A. H., Makhloof, A. A., Mahmoud, A. A., & Galal, A. A. (2012). Geotechnical Behavior of Pliocene Sedimentary Rocks Exposed along Qena-Safaga Road at Qena Region, Egypt. International Mining Engineering and Mineral Processing, 1, 84-93. https://doi.org/10.5923/j.mining.20120102.10

  15. 15. Ismail, I. S. (2000). Application of Geophysical Techniques for Engineering Purposes and Delineating the Underground Water at New Tiba City, Luxor, Egypt. Ph.D. Thesis, Qena: South Valley University.

  16. 16. Issawi, B. (1972). Review of the Upper Cretaceous-Lower Tertiary Stratigraphy in Central and Southern Egypt. AAPG Bulletin, 55, 1448-1463.

  17. 17. Issawi, B., Abdallah, A. M., & Said, M. (1978). Geology of Wady El-Mashash Area. Eastern Desert, Egypt, 8, 163-185.

  18. 18. Krasheninnikov, V. A., & Penikarov, V. P. (1964). Zonal Stratigraphy of Paleogene in the Nile Valley (No. 32, p. 26). Cairo: Geol. Survey an Min., Res. Dep.

  19. 19. Makhloof, A. A., Mahmoud, A. A., Ismaiel, H. A. H., & Galal, A. A. (2013). Evaluation and Interpretation of Cracks along Qena-Safaga Road Using Surveying Techniques. Minia Journal of Engineering and Technology, 32, 194-203.

  20. 20. Mostafa, T., Abd el-aziz, K., & Gad-Elkareem, A. M. (2016). Ambient Noise for Determination of Site Dynamic Properties at Hurghada and Safaga Cities, Red Sea, Egypt. Acta Geodynamica et Geomaterialia, 13, 227-240. [Paper reference 1]

  21. 21. Philiobbos, E. R. (1969). Geology of the Phosphorites of the Nile Valley. PhD Thesis, Assiut: Assiut Uniersity.

  22. 22. Sabry, H. (1968). Stratigraphy and Classification of Type Esna Group of Egypt. AAPG Bulletin, 52, 1792-1793.

  23. 23. Said, R. (1962). The Geology of Egypt (p. 337). Amsterdam, New York: Elsevier Pub. Co.

  24. 24. Said, R. (1971). Exploration Notes to Accompany the Geological Map of Egypt (No. 56, p. 123).

  25. 25. Said, R., & Sabry, H. (1964). Planktonic Foraminifera from the Type Location of Esna Shale in Egypt. Micro-Paleontology, 10, 375-395. https://doi.org/10.2307/1484585

  26. 26. Sawires, R., Pelaez, J. A., Fat-Helbary, R. E., & Ibrahim, H. A. (2016). A Review of Seismic Hazard Assessment Studies and Hazard Description in the Building Codes for Egypt. Acta Geodaetica et Geophysica, 51, 151-180. https://doi.org/10.1007/s40328-015-0117-5 [Paper reference 1]

  27. 27. Wuest, R. A. J., & McLane, J. (2000). Rock Deterioration in the Royel Tomb of Seti I, Valley of the Kings, Luxor, Egypt. Engineering Geology, 58, 163-190. https://doi.org/10.1016/S0013-7952(00)00057-0

  28. 28. Yesiller, N., Hanson, J. L., Rener, A. T., & Usmen, M. A. (2001). Ultrasonic Testing for Evaluation of Stabilized Mixtures, Geomaterials. Transportation Research Record, 1757, 32-39. https://doi.org/10.3141/1757-04

  29. 29. Youssef, A. M., Pradhan, B., Gaber, A. F. D., & Buchroithner, M. F. (2009). Geomorphological Hazard Analysis along the Egyptian Red Sea Coast between Safaga and Quseir. Natural Hazards and Earth System Sciences, 9, 751-766. https://doi.org/10.5194/nhess-9-751-2009