Soft Nanoscience Letters
Vol.3 No.2(2013), Article ID:29656,8 pages DOI:10.4236/snl.2013.32006

Banana Peel Carbon Containing Functional Groups Applied to the Selective Adsorption of Au(III) from Waste Printed Circuit Boards

Huajun Zheng1,2*, Limin Wang1

1Department of Applied Chemistry, Zhejiang University of Technology, Hangzhou, China; 2State Key Laboratory Breeding Base of Green Chemistry Synthesis Technology, Zhejiang University of Technology, Hangzhou, China.

Email: *zhenghj@zjut.edu.cn

Copyright © 2013 Huajun Zheng, Limin Wang. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Received December 28th, 2012; revised January 23rd, 2013; accepted February 3rd, 2013

Keywords: Banana Peel Carbon; Adsorption; Gold(III); Printed Circuit Boards

ABSTRACT

This paper reports a kind of banana peel carbon (BPC) containing -OH, -NH2 functional groups which prepared through controlling carbonization temperature and its application on the selective adsorption of gold from waste printed circuit boards (PCBs). The adsorption of BPC for Au(III) reached equilibrium in 30 min and the adsorption of Au(III) was favorable at pH 2.5. Meanwhile, the adsorption isotherm showed the maximum adsorption capacity of 801.7 mg/g for Au(III). The results displayed that BPC had a strong selectivity for Au(III) and a negligible affinity to base metal ions, such as Cu(II), Ni(II), Fe(III) and Pb(II). The BPC adsorbent, which absorbed gold, can be recovered completely by HCl-thiourea solution.

1. Introduction

The rapidly growing of electronic waste (e-waste), especially the discarded printed circuit boards (PCBs), is creating negative impacts on the environment and also bringing serious problems concerning the waste of metal resources. According to Zhou et al. and Veit et al. [1,2], about 130 kg copper, 20 kg tin, 24 kg lead, 18 kg nickel, and 0.45 kg gold are included in each ton of PCBs. What’s more, it is important to know that many harmful materials like brominated flame retardant which are highly toxic to the environment are also contained in PCBs. Hence, recycling and reusing the metal resources, especially the precious metals from waste PCBs are important subjects from the points of environment and economy.

As known, precipitation, electrowinning, solvent extraction, carbon and resin adsorption are several common methods for recovery gold from various forms of the lixivium of PCBs [3-9]. Activated carbon (AC), a common adsorbent, was employed to recovery of gold from PCBs due to its relative high-efficiency and lowcost. However, its poor selectivity to some base metal ions (Cu(II), Ni(II), Fe(III), Pb(II)) and small adsorption capacities for gold ions are fatally defects for AC, which limit its wide application on gold adsorption from PCBs. The poor selectivity of AC was due to the lack of specific functional groups, while for many natural materials, such as banana peel (BP) that is mainly composed of polymers such as lignin, hemicellulose and pectins, not only have developed biological cell structure but also contain rich organic functional groups (-OH, -NH2, -COOH) [10-12]. Some investigations had reported that dried BP could directly extract Cu(II), Cr(IV), Cd(II), Pb(II) and phenolic compounds from aqueous solution due to their pore structures and functional groups (-OH, -COOH, -NH2) on the surface of pores [13-17]. Furthermore, BP extract could be used for the reduction of palladium, gold and silver salts that might attributed to the functional groups and polymers as well as the proteinaceous matter contained in BP [18-20]. BP can also be used for the preparation of porous carbons that own big specific surface area through the etching of chemical activator and carbonization at certain temperature [21].

In this work, we have designed a preparation method of BPC with functional groups (-OH, -NH2) through controlling the carbonization temperature of BP. BPC as adsorbent, was tested in the adsorption of Au(III) from gold chloride solution with different concentration, contact time and pH value. At the same time, gold recovery and adsorbent regeneration were investigated. The selectively recovery of Au(III) from the lixivium of PCBs was also studied.

2. Experimental

2.1. Materials

Gold chloride (AuCl3, ≥99.9%), hydrochloric acid (HCl, 36% - 38%), sodium hydroxide (≥96.0%), ammonia liquor (NH3, 25% - 28%), ammoniumchloride (≥99.5%), ethylenediamine (C2H8N2, ≥99.0%), sodium chlorate (≥ 99.0%), sodiumchloride (≥99.5%),thiourea (≥99.0%), and other chemicals were purchased from Aldrich, China. All chemicals were used as received without further purification. Deionized water was used in all aqueous solution.

Banana peels were obtained from normal ripe yellow bananas (Sesame Banana, Guangdong Province, China) and the waste PCBs were derived from discarded computer motherboard, which were purchased from local supermarket and electronic waste market, respectively.

2.2. Preparation and Characterization

2.2.1. Preparation of BPC

The detailed procedure for preparing BPC was introduced as follows. Firstly, the BP used for experiment were washed with deionized water thoroughly, and dried in a hot-air oven at 80˚C for 2 days. After that the brownish dry peels were ground to fine powder using an electrically operated mill, and then passed through 100 mesh sieve (150 μm) to obtain experimental BP powder. Finally, the pyrolysis of BP was performed at 500˚C for 4 hours under flowing nitrogen at a heating rate of 5˚C/min to obtain BPC. The BPC is stirred manually to mix well. There are little difference between batches because the environments of the sources’ growing are similar.

2.2.2. Characterization

Thermal gravimetric (TG) analysis was carried out using a Netzsch STA449C thermo analysis instrument in the temperature range of 30˚C - 900˚C at a heating rate of 10˚C /min under nitrogen. The Fourier transform infrared (FTIR) spectra were collected with a Nicolet 670 spectrometer with an attenuated total reflectance (ATR) apparatus. Energy dispersive X-ray analysis (EDX) spectroscopy was performed with a KRATOS AXIS ULTRA (DLD). Nitrogen sorption isotherms of the samples were measured at 77 K using a Micromeritics ASAP 2020MC analyzer. The specific surface areas were calculated with the Brunauer, Emmett and Teller (BET) method and the pore size distributions were calculated using the Barrett-Joyner-Halenda (BJH) model applied to the desorption branch of the N2 isotherms.

2.3. Adsorption Performance for Au(III)

A series of 10 mL of gold chloride solution were transferred to 50 mL beaker and about 0.01 g of adsorbent was added to each vessel. The suspensions were stirred mechanically in a shaker bath at 1 - 120 min intervals at room temperature (30˚C) to examine the kinetic reaction. The effect of pH on the adsorption process was investigated in a range of 1 - 5 and small amounts of dilute HCl and NaOH solution were added to adjust the pH value. The adsorbent mass, solution concentration, and volume were the same as described above. The adsorbents and solutions were separated through the common filter device and the suspensions were almost completed separated. After that the concentration of gold ion was determined by atomic absorption spectrometry (AAS, Varian AA220) using an air-acetylene flame and electro thermal atomization with 242.8 nm as a resonance line as well as the slit width with 1 nm. The adsorption capacity and efficiency of Au(III) taken up by BPC were determined using aliquots of 10 mL in a concentration interval, the calculation methods was according to the following equation:

(1)

(2)

where A (%) is the adsorption efficiency, Qe (mg/g) is the adsorption capacity, C0 (mg/L) and Ce (mg/L) are the initial and final concentrations of metal ions, respectively. V (L) is the solution volume and m (g) is the weight of adsorbent used for experiments.

2.4. Gold Recovery and Adsorbent Regeneration

The recovery of adsorbed gold and the regeneration of BPC adsorbent were investigated using 0.7 M thiourea - 2 M HCl. The adsorbent (0.10 g) which adsorbed Au(Ⅲ) was washed with deionized water several times and transferred into reagent bottles with lids. After that the desorption agent (20 mL) was added, and then the mixtures were stirred at room temperature using magnetic stirrer for 4 hours. The content of gold still combined with BPC adsorbent was tested by EDX analysis.

2.5. Extraction of Au(III) from PCBs

The sample of the lixivium of PCBs was obtained from laboratory leaching method. The procedure was briefly introduced as follows. First, 50 g of PCBs powder was added to 500 mL solution of ammonia water-ammonium chloride-ethanediamine (4 M:4 M:1 M) in an opened reactor. The suspensions was stirred mechanically for 5 hours, and at the same time, 100 mL of 30% hydrogen peroxidewas dropwise added to the aboved mixture in the whole experiment. After that 5.0 g of sodium chlorate and 75 mL of hydrochloric acid (3 M) as well as 5.0 g of PCBs powder already removed copper were mixed at a 250 mL open reactor using a shaker, allowed to stir 5 hours at room temperature (30˚C). The sample of the lixivium was finally obtained by filtering and its pH value was adjusted to 2.5.

0.05 g of BPC was added to 50 mL sample solutions and the mixture were stirred for 3 hours to achieve equilibrium at room temperature. The adsorbents were filtered after adsorbed ions and metal concentrations were analyzed by AAS.

3. Results and Discussion

3.1. Characterization for BPC

Figure 1 is the thermo gravimetric (TG) curve of raw BP, which was analysised at a heating rate of 10˚C /min with a nitrogen flow. As shown in Figure 1, The initial weight loss in the region 50˚C - 200˚C was mainly due to moisture and bonding water evaporation adsorbed to the banana peel. The temperature region ranging from 200˚C - 700˚C was mainly attributed to thermal depolymerization of hemicellulose, cleavage of glycosidic linkages of cellulose and lignin components as well as the decomposition of some biomass, such as proteinaceous matter or ester [22]. After 700˚C, further pyrolyzation of biomass in BP was occured, and almost all the natural organic groups were cracked at this stage. The overview of the elemental analysis of raw BP and BPC at different carbonization temperature are given in Table 1. As listed in Table 1, trogen, potassium, chlorine, silicon and phos

Figure 1. TG curve of raw BP.

phorus elements. The raw BP contained 59.08 wt% of carbon, 35.33 wt% of oxygen, and 0.21 wt% of nitrogen. The content of nitrogen was gradually decreased from 1.31 wt% to 0.29 wt% with the temperature increased from 500˚C to 700˚C. These dates proved that 200˚C - 700˚C was the appropriate temperature region for preparing porous carbon materials based on banana peels.

Figure 2 shows the FT-IR spectra of raw banana peel powder and porous carbon materials after carbonization at 300˚C, 500˚C, 700˚C, respectively. As it can be seen from Figure 2(a), the adsorption bands appearing at 3400, 2924, 2854, 1730 and 889 cm1 were assigned to O-H stretching of hydroxyl, C-H stretching of alkane, C-H and C=O stretching of carboxylic acid or ester and N-H deformation of amine, respectively [23]. The adsorption peaks appearing at the region of 1600 - 950 cm1 were attributed to ester, polysaccharide or protein, which have a strong affinity to both gold metal ion and base metal ions, such as copper, iron, nickel, lead. As seen from (Figure 2(c)), compared with that of raw banana peel (Figure 2(a)), the prominent peak intensity at 3400, 2924, 2854 , 1730 and 1600 - 950 cm1 that attributed to the stretching of O-H, C-H and C=O, was significantly reduced, confirming the damage of polysaccharide or protein in porous carbon materials after carbonization at 500˚C. Fortunately, the adsorption bands appearing at 889 cm1 that attributed to N-H deformation of amines was retained, which would together for the adsorption of Au(III) with hydroxyl group. From Figures 2(b) and (d), it can be clearly seen that the adsorption peaks at 2924, 2850 cm1 assigned to C-H for porous carbon materials after carbonization at 300˚C (Figure 2(b)) still existed, while for the materials after treated at 700˚C (Figure 2(d)), the adsorption peak of -NH2 was disappeared. Therefore, 500˚C was choosed as the best temperature for carbonization of banana peel.

Figure 3 displays N2 adsorption-desorption isotherms and pore-size distribution of BP and BPC-500˚C. As shown in Figure 3(a), the Type-IV isotherms for BPC- 500˚C with a desorption hysteresis in P/P0 ranged from 0.6 to 0.8 suggested the existence of developed mesopores. The steep increase in the adsorbed volume at the low relative pressure was related with the presence of micropores, and the almost vertical tails at a relative pressure near to 1.0 revealed the presence of macropores. The BET surface area of BPC-500˚C was 6.70 m2/g with the total pore volume of 0.018 cm3/g as well as the average pore size of 10.17 nm. In contrast, the nitrogen sorption isotherm was an approximately typical Type-I for BP and the BET surface area was 1.79 m2/g. The pore size distributions of BP and BPC-500˚C calculated from the nitrogen desorption branches are given in Figure 3(b). BPC-500˚C displayed typical hierarchical pore size dis

Table 1. Element content of BP and BPC at different temperature.

Figure 2. The FT-IR spectra of (a) raw banana peel powder and (b, c, d) porous carbon materials after carbonization at 300˚C, 500˚C, 700˚C, respectively.

tribution with a highest peak centering at ca. 23.9 nm, as well as several lower peaks centering at ca. 3.5, 10.4, 12.3 and 16.3 nm. It can be clearly observed that the majority of pores of BPC-500˚C were located in the region of mesopores. In comparison, the pore sizes of BP were located in the region of micropores. The detailed physical properties of BP and BPC at different carbon temperatures are tabulated in Table 2.

3.2. Adsorption Experiments

The adsorption performance and adsorbent mass as well as the solution concentration of BPC-500˚C adsorption for Au(III) are summarized in Table 3. It showed that the adsorption capacity of BPC-500˚C gradually increased from 531.36 to 801.70 mg/g with the increase of gold chloride concentration from 627 to 1354 mg/L, while the adsorption efficiency decreased from 99.99% to 69.86%. The great adsorption capacity of BPC-500˚C may be attributed to the high affinity of hydroxyl or amino functional groups for Au(III), however the adsorbed gold ion will be reduced to gold element due to the special chemical structure and crystal defect of carbonaceous material, which creates active site vacancies for further adsorption [24]. Besides, the high specific surface area

(a)(b)

Figure 3. (a) N2 adsorption-desorption isotherms at 77 K and (b) BJH pore size distributions for BP and BPC-500˚C.

Table 2. Physical properties of BP and BPC.

and pore volume of the material might also play a role in gold adsorption process. The adsorption performance of BPC at different carbonization temperatures gave in Table 4 showed an interesting trend between adsorption

Table 3. Adsorption performance of BPC-500℃ for Au(III) in different concentrations.

Table 4. Adsorption performance of BP and BPC for Au(III).

capacity and carbonization temperature. It displayed that the adsorption capacity of the adsorbent gradually increased from 198.31 to 801.70 mg/g with the carbonization temperature increased from 80˚C to 500˚C, while the adsorption capacity decreased to 71.19 mg/g with the carbonization temperature increased to 700˚C . The reason is because the reductive group (-COOH) and organic biomass (polysaccharide, protein, ester, etc.) were not completely decomposed at the temperature below 500˚C, while the functional groups (-OH, -NH2) responsible for gold adsorption were also decomposed at the temperature over 500˚C. The results indicated that 500˚C was the best temperature for preparation BPC adsorbent.

Figure 4(a) describes the relationship between pH and adsorption efficiency of BPC for Au(III). As shown, BPC can easily extraction Au(III) in acidic environment, it owned more than 83.27% adsorption efficiency in pH 2.5 and about 48.43%, 78.94%, 71.46% in pH 1.0, 3.5 and 5.0, respectively. The explanation is that the high concentration of H(I) species leading to the protonation of main groups (-OH, -NH2) responsible for metal extraction, and the surface of the adsorbent is positively charged which made the adsorbent less able to accommodate the adsorption of Au(III) ions [25]. While at pH higher than 4.0, the metal solution becomes unstable and gold ion will in the risk of hydrolysis. Thus, pH 2 - 3 was the best region for BPC adsorbent to adsorb Au(III), especially pH 2.5 according to experiments. Simultaneously, the effect of contact time on adsorption capacity was plotted in Figure 4(b). As can be seen, the adsorption process was so fast, reaching equilibrium in 30 min.

3.3. Gold Recovery and Adsorbent Regeneration

The X-ray photoemission spectra of Au-BPC and (Au 4f5/2, 4f7/2) are given in Figure 5. Figure 5(a) displayed the C 1s, O 1s, O KLL, K 2s, K 2p, Si 2s, Mg 1s, Mg KLL, Au 4d and Au 4f core level spectra recorded from the Au-BPC material, indicated that gold was absorbed on the BPC which was in accordance with the EDX pat-

(a)(b)

Figure 4. The effect of (a) pH and (b) contact time on the extraction of Au(III).

terns of Au-BPC Figure 5(a). As shown in Au 4f XPS spectrum Figure 5(b), two peaks located at 84.08 and 87.73 eV (after carbon correction) can be attributed to Au 4f7/2 and Au 4f5/2, respectively. This pair of peaks indicated that Au is present in its elemental state, which suggested that the gold ion had been reduced to element gold on the surface of BPC.

Figure 6 is the EDX patterns of BPC-500˚C adsorbent after Au(III) adsorption and desorption, respectively. Clearly, considerable amount of gold-containing species on the BPC after adsorption Figure 6(a) were removed after 2M HCl - 0.7 M thiourea treatment Figure 6(b). As known, the adsorbed gold ion was already reduced to gold and the gold could be resolved in acidic solutions of thiourea in the presence of oxidant according to Murthy [26]. The results indicated that the adsorbent material can be successfully recovered.

3.4. Extraction of Au(III) from the Lixivium of PCBs

Figure 7 depicts the selective extraction of Au(III) on

(a)(b)

Figure 5. The XPS spectrum of (a) Au-BPC and (b) Au 4f.

(a)(b)

Figure 6. The EDX patterns of BPC after (a) absorbed and (b) desorbed gold.

BPC from multiple lixivium of PCBs. From Figure 7(a), it can be seen that the concentrations of Au(III), Cu(II), Ni(II), Fe(III) and Pb(II) in lixivium were 0.54, 643, 125, 3.29 and 499 mg/L, and the concentrations became 0.00, 639, 120, 2.56 and 442 mg/L, respectively, after adsorbed by BPC-500˚C adsorbent (Figure 7(b)). It was easily known that the adsorption efficiency was 99.99 % of Au(III), and 0.62% of Cu(II), 4.00% of Ni(II), 22.19% of Fe(III), and 11.42% of Pb(II). This is mainly because of that the reductive group (-COOH) and organic biomass (polysaccharide, protein, ester, etc.) that participate in complex some base metal ions in banana peels were decomposed in the carbonization process, and the functional groups (-OH, -NH2) that have a lone pair of electrons could produce coordination compound with Au(III) that had unpaired and unstable d-electrons [27]. The results displayed that BPC-500˚C adsorbent owned strong affinity for Au(III) and tiny affinity for other base metal ions.

(a)(b)

Figure 7. Compositions of the gold leaching solutions from PCB (a) before and (b) after adsorbed by BPC-500˚C adsorbent (0.05 g per 50 mL solution, pH 2.5 and T = 303 ± 2 K).

4. Conclusion

BPC that containing functional groups as adsorbent displays an outstanding adsorption performance for Au(III). This material is very attractive due to its low cost and simple carbonization process. More than that, the high selectivity and adsorption capacity (801.70 mg/g) for Au(III) at pH 2.5 are important aspects for recovery high purity gold from PCBs resources. Furthermore, the gold can simply be recovered by stripping with HCl-thiourea agent.

5. Acknowledgements

The financial support from Zhejiang major social development of major scientific and technological special projects (NO. 2010C13017) is gratefully acknowledged.

REFERENCES

  1. G. W. Y. H. Zhou and K. Q. Qiu, “A New Technology for Recycling Materials from Waste Printed Circuit Boards,” Journal of Hazardous Materials, Vol. 175, No. 1-3, 2010, pp. 823-828. doi:10.1016/j.jhazmat.2009.10.083
  2. H. M. Veit, A. M. Bernardes, J. Z. Ferreira, J. A. S. Tenorio and C. D. Malfatti, “Recovery of Copper from Printed Circuit Boards Scraps by Mechanical Processing and Electrometallurgy,” Journal of Hazardous Materials, Vol. 137, No. 3, 2006, pp. 1704-1709. doi:10.1016/j.jhazmat.2006.05.010
  3. S. Syed, “Recovery of Gold from Secondary Sources—A Review,” Hydrometallurgy, Vol. 115, 2012, pp. 30-51. doi:10.1016/j.jhazmat.2006.05.010
  4. A. C. Grosse, G. W. Dicinoski, M. J. Shaw and P. R. Haddad, “Leaching and Recovery of Gold Using Ammoniacal Thiosulfate Leach Liquors—A Review,” Hydrometallurgy, Vol. 69, No. 1-3, 2003, pp. 1-21. doi:10.1016/S0304-386X(02)00169-X
  5. K. Hidetaka, Y. Ri, P. Durga, O. Keisuke, H. Hiroyuki and I. Katsutoshi, “Recovery of Gold from Hydrochloric Acid by Means of Selective Coagulation with Persimmon Extract,” Separation Science and Technology, Vol. 43, No. 9-10, 2008, pp. 2375-2385. doi:10.1080/01496390802151716
  6. J. Y. Park and D. J. Fray, “Recovery of High Purity Precious Metals from Printed Circuit Boards,” Journal of Hazardous Materials, Vol. 164, No. 2-3, 2009, pp. 1152- 1158. doi:10.1016/j.jhazmat.2008.09.043
  7. P. Navarroa, C. Vargasa, M. Alonsob and F. J. Alguacil, “Towards a More Environmentally Friendly Process for Gold: Models on Gold Adsorption onto Activated Carbon from Ammoniacal Thiosulfate Solutions,” Desalination, Vol. 211, No. 1-3, 2007, pp. 58-63. doi:10.1016/j.desal.2006.03.590
  8. M. I. Jeffrey, D. M. Hewitt, X. Dai and S. D. Brunt, “Ion Exchange Adsorption and Elution for Recovering Gold Thiosulfate from Leach Solutions,” Hydrometallurgy, Vol. 100, No. 3-4, 2010, pp. 136-143. doi:10.1016/j.hydromet.2009.11.003
  9. E. Y. Kim, M. S. Kim, J. C. Lee and B. D. Pandey, “Selective Recovery of Gold from Waste Mobile Phone PCBs by Hydrometallurgical Process,” Journal of Hazardous Materials, Vol. 198, 2011, pp. 206-215. doi:10.1016/j.jhazmat.2011.10.034
  10. M. Soleimani and T. Kaghazchi, “The Investigation of the Potential of Activated Hard Shell of Apricot Stones as Gold Adsorbents,” Journal of Industrial and Engineering Chemistry, Vol. 14, No. 1, 2008, pp. 28-37. doi:10.1016/j.jiec.2007.06.003
  11. D. Parajuli, C. R. Adhikari, H. Kawakita, S. Yamada, K. Ohto and K. Inoue, “Chestnut Pellicle for the Recovery of Gold,” Bioresource Technology, Vol. 100, No. 2, 2009, pp. 1000-1002. doi:10.1016/j.biortech.2008.06.058
  12. P. A. M. Teirlinck and F. W. Petersen, “The Nature of Gold-Iodide Adsorption onto Coconut-Shell Carbon,” Minerals Engineering, Vol. 9, No. 9, 1996, pp. 923-930. doi:10.1016/0892-6875(96)00084-2
  13. R. S. D. Castro, L. Caetano, G. Ferreira, P. M. Padilha, M. J. Saeki, L. F. Zara, M. A. U. Martines and G. R. Castro, “Banana Peel Applied to the Solid Phase Extraction of Copper and Lead from River Water: Preconcentration of Metal Ions with a Fruit Waste,” Industrial & Engineering Chemistry Research, Vol. 50, No. 6, 2011, pp. 3446-3451. doi:10.1021/ie101499e
  14. J. R. Memon, S. Q. Memon, M. I. Bhanger, A. El-Turki, K. R. Hallam and G. C. Allen, “Banana Peel: A Green and Economical Sorbent for the Selective Removal of Cr(VI) from Industrial Wastewater,” Colloids Surfaces B: Biointerfaces, Vol. 70, No. 2, 2009, pp. 232-237. doi:10.1016/j.colsurfb.2008.12.032
  15. J. Anwar, U. Shafique, Waheed-uz-Zaman, M. Salman, A. Dar and S. Anwar, “Removal of Pb(II) and Cd(II) from Water by Adsorption on Peels of Banana,” Bioresource Technology, Vol. 101, No. 6, 2010, pp. 1752-1755. doi:10.1016/j.biortech.2009.10.021
  16. J. Q. Albarelli, R. B. Rabelo, D. T. Santos, M. M. Beppu and M. A. A. Meireles, “Effects of Supercritical Carbon Dioxide on Waste Banana Peels for Heavy Metal Removal,” Journal of Supercritical Fluids, Vol. 58, No. 3, 2011, pp. 343-351. doi:10.1016/j.supflu.2011.07.014
  17. M. Achak, A. Hafidi, N. Ouazzani, S. Sayadi and L. Mandi, “Low Cost Biosorbent “Banana Peel” for the Removal of Phenolic Compounds from Olive Mill Wastewater: Kinetic and Equilibrium Studies,” Journal of Hazardous Materials, Vol. 166, No. 1, 2009, pp. 117-125. doi:10.1016/j.jhazmat.2008.11.036
  18. A. Bankar, B. Joshi, A. R. Kumar and S. Zinjarde, “Banana Peel Extract Mediated Novel Route for the Synthesis of Silver Nanoparticles,” Colloids Surfaces A: Physicochemical and Engineering Aspects, Vol. 368, No. 1-3, 2010, pp. 58-63. doi:10.1016/j.colsurfa.2010.07.024
  19. A. Bankar, B. Joshi, A. R. Kumar and S. Zinjarde, “Banana Peel Extract Mediated Synthesis of Gold Nanoparticles,” Colloids Surfaces B: Biointerfaces, Vol. 80, No. 1, 2010, pp. 45-50. doi:10.1016/j.colsurfb.2010.05.029
  20. A. Bankar, B. Joshi, A. R. Kumar and S. Zinjarde, “Banana Peel Extract Mediated Novel Route for the Synthesis of Palladium Nanoparticles,” Materials Letters, Vol. 64, No. 18, 2010, pp. 1951-1953. doi:10.1016/j.matlet.2010.06.021
  21. Y. K. Lv, L. H. Gan, M. X. Liu, W. Xiong, Z. J. Xu, D. Z. Zhu and D. S. Wright, “A Self-Template Synthesis of Hierarchical Porous Carbon Foams Based on Banana Peel for Supercapacitor Electrodes,” Journal of Power Sources, Vol. 209, 2012, pp. 152-157. doi:10.1016/j.jpowsour.2012.02.089
  22. B. Deepa, E. Abraham, B. M. Cherian, A. Bismarck, J. J. Blaker, L. A. Pothan, A. L. Leao, S. F. de Souza and M. Kottaisamy, “Structure, Morphology and Thermal Characteristics of Banana Nanofibers Obtained by Steam Explosion,” Bioresource Technology, Vol. 102, No. 2, 2011, pp. 1988-1997. doi:10.1016/j.biortech.2010.09.030
  23. J. R. Memon, S. Q. Memon, M. I. Bhanger, G. Z. Memon, A. El-Turki and G.C. Allen, “Characterization of Banana Peel by Scanning Electron Microscopy and FT-IR Spectroscopy and Its Use for Cadmium Removal,” Colloids and Surfaces B: Biointerfaces, Vol. 66, No. 2, 2008, pp. 260-265. doi:10.1016/j.colsurfb.2008.07.001
  24. R. Chand, T. Watari, K. Inoue, H. Kawakita, H. N. Luitel, D. Parajuli, T. Torikai and M. Yada, “Selective Adsorption of Precious Metals from Hydrochloric Acid Solutions Using Porous Carbon Prepared from Barley Straw and Rice Husk,” Minerals Engineering, Vol. 22, No. 15, 2009, pp. 1277-1282. doi:10.1016/j.mineng.2009.07.007
  25. K. F. Lam, K. L. Yeung and G. McKay, “An Investigation of Gold Adsorption from a Binary Mixture with Selective Mesoporous Silica Adsorbents,” Journal of Physical Chemistry B, Vol. 110, No. 5, 2006, pp. 2187-2194. doi:10.1021/jp055577n
  26. D. S. R. Murthy, V. Kumar and K. V. Rao, “Extraction of Gold from an Indian Low-Grade Refractory Gold Ore through Physical Beneficiation and Thiourea Leaching,” Hydrometallurgy, Vol. 68, No. 1-3, 2003, pp. 125-130. doi:10.1016/S0304-386X(02)00197-4
  27. H. S. Zou, Z. Q. Chu and G. Lin, “A Novel Recovery Technology of Trace Precious Metals from Waste Water by Combining Agglomeration and Adsorption,” Transactions of Nonferrous Metals Society of China, Vol. 17, No. 4, 2007, pp. 858-863. doi:10.1016/S1003-6326(07)60188-5

NOTES

*Corresponding author.