Received 11 December 2015; accepted 16 January 2016; published 19 January 2016

ABSTRACT

Thin-wall injection molded parts have been paid much attention to the lightweight saving from viewpoints of natural resources saving. In the injection molding, skin-core structure can be found in the parts. This skin-core structure affects the property of completed injection molding parts (bulk property) even if in thin-wall injection molding. However, there is a few research about the relationship between bulk property and internal property distribution in the injection molding specimen. In this study, thin-wall injection molded parts of polypropylene (PP) were prepared by 4 different molecular weight and molecular weight distribution to reveal the relationship between bulk property and property distribution. These characteristics were investigated by using tensile test, fracture toughness characterized by Essential Work of Fracture (EWF) method for bulk property and film tensile test by sliced sample for tensile property distribution. The property distribution test results revealed that the highly bulk property sample had thicker highly mechanical property layer on its surface.

Keywords:

Molecular Weight, Molecular Weight Distribution, Fracture Toughness, Property Distribution, Thin-Wall, Injection Molding

1. Introduction

Injection molding is one of the most popular methods to make plastic products. The parts made by this technique were used in various situations such as transportation equipment, electric appliance, and supplies. Recently, light-weighting is very important theme because their weight-saving causes low emission of carbon dioxide, convenience and economy. The one of the simple ways to light-weighting is thin-wall injection molding. However, the resin was rapidly cooled by mold, so that the skin and core layer of molding article formed different structure and this structure influenced bulk property strongly [1] -[4] . This heterogeneous structure which is called skin-core structure is formed even if it is a thin-wall. It was known that the percentage of this skin layer thickness to the injection molded specimen thickness increased as decreased the specimen thickness [5] . So it is very important to understand the relationship between bulk mechanical property and mechanical property distribution by the difference of heterogeneous skin-core structure. In recent researches, effect of β phase crystalline nucleating agent added polypropylene (PP) [6] and influence of ultra-high speed injection molding [7] were studied to reveal the relationship between non-uniform structure and property of thin-wall injection molding products. Moreover, this non-uniform structure-property relationship was also investigated in composite material [8] and non-olefin resin based materials [9] . Nevertheless, molecular weight and molecular weight distribution effects on structure-property relationship of thick-wall materials were well studied [10] -[12] . Comparably, it has not been reported in the case of thin-wall injection molding products. Besides, there were a number of reports about injection molding products in various conditions, but almost reports focused on only internal structure or property. Especially in property measurement, most researchers focused on the properties of entire cross- section in injection molding product. However, property distribution which has the strong relationship with skin- core structure has not been hardly studied except hardness and scratch resistance property of surface [13] - [17] . In this research, the relationship between bulk mechanical property and mechanical property distribution of thin-wall injection molded polypropylene with different molecular weight and molecular weight distribution was investigated. The bulk mechanical properties were characterized in terms of static tensile property and fracture toughness by using essential work of fracture method [18] . The mechanical property distribution was measured by tensile test with thin-sliced dumbbell film obtained from bulk specimen.

2. Experimental

2.1. Material & Injection Molding Conditions

In this study, 4 different kinds of homo-PP resins were used. The molecular characteristics were summarized in Table 1. These resins had different molecular weight and distribution [12] . In Table 1, there are 4 types of PP resins were expressed by using two characters. H and L describe higher and lower molecular weight respectively. N, M and W describe narrow, middle and wide molecular weight distribution respectively. Thin-wall specimen was prepared by injection molding. Resin temperature and mold temperature were controlled 240˚C and 40˚C. Packing pressure, holding pressure and cooling time were 50, 30 MPa and 20 seconds. Injection speed was controlled at 100 mm/s.

2.2. Tensile Test

To measure the static tensile property behavior, tensile properties were measured using anuniversal testing machine (Instron Corp., Type; 55R4206). The 1 mm thick dumbbell specimen (JIS K-7162-1BA) was used and the longitudinal direction was set along the FD direction. Tensile tests were performed under room temperature (RT) condition at a crosshead speed of 10 mm/min.

2.3. Essential Work of Fracture Method

Fracture toughness of thin-wall specimens was evaluated by EWF tests using the universal testing machine with double edge notched specimens (see Figure 1). The dimension of the test piece was 100 × 20 × 1 mm and longitudinal direction was set along the FD direction. U-shaped notch with 2 mm width was introduced followed by a 1 mm initial crack at the tip of the U-notch. A ligament length was varied by the depth of U-notch as 3, 4, 5, 6, and 7 mm. The test was performed under RT condition at a crosshead speed of 10 mm/min. In EWF method, the energy for destruction of specimen W_f is divided into the energy of deformation in plastic zone W_e and crack propagation in the process zone W_p (See Equation (1)). Equation (2) was given by each fracture energy per unit area from Equation (1) and the energy for destruction of specimen per unit area w_fwas given to divide the Equation (2) by the area of ligament part. In Equation (3), w_eis the essential fracture toughness of the specimen.

(1)

(2)

(3)

where, l is ligament length, t is the thickness of the specimen, and φ is shape factor of plastic zone.

2.4. Tensile Test

To measure the difference of mechanical property distribution, tensile property distribution was measured using universal testing machine. The samples were sliced into every 50 μm thick films from the sample surface to 500 µm in depth with a rotary microtome (Leica Biosystems Ltd., RM2235) at room temperature. After this thin- sliced process, dumbbell specimen (JIS K-6251-7) for tensile property distribution was stamped out. The selected sample layers were 0 - 50, 50 - 100, 100 - 150, 150 - 200, 200 - 250 and 450 - 500 μm depth from the surface on each sample.

3. Results and Discussion

3.1. Static Tensile Property

Figure 2 shows the stress-strain curves of the 4 different samples from tensile test. Figure 2(a) is the full stress- strain curve and Figure 2(b) is elongated stress-strain curve around yield point. Low molecular weight samples (LN and LM) did not break in this test. On the other hand, high molecular weight samples (HM and HW) were broken and HM showed lower strain at break than HW. In Figure 2(b), there is quick drop between the strains of 15% - 20% in LN LM, and HW. According to the decreasing the molecular weight and increasing molecular weight distribution, this quick drop value increase. It is known that the decreasing molecular weight affects the clarification of necking behavior [19] , this quick drop caused by necking. Table 2 shows the results of tensile test. HM showed higher modulus and yield stress than LM so high molecular weight affects the increasing modulus and yield stress. As compared with LN and LM, LN showed higher modulus and yield stress than LM. This behavior was also measured in comparison of HM with HW, hence it is considered that the narrower molecular weight distribution affects the increasing of the modulus and yield stress because narrower molecular weight distribution sample has highly molecular orientation toward to FD direction near the surface than broad molecular weight distribution sample [12] .

3.2. Fracture Toughness

Figure 3 shows the results of fracture toughness obtained by EWF tests. The fracture toughness we of LN, LM, HM and HW were 21.5, 14.8, 23.5 and 18.3 kJ/mm², respectively. In LM and HM, HM showed higher fracture toughness than LM. It was indicated that the high molecular weight affected the high fracture toughness. In LN and LM, the narrow molecular weight distribution sample showed higher fracture toughness as compared with the wider that. In the case of HM and HW, the fracture toughness indicated the same tendency with LN and LM. From these results, it was found that the higher molecular weight and the narrower molecular weight distribution affect the increasing of the fracture toughness.

3.3. Tensile Property Distribution

Figure 4 shows the stress-strain curve obtained by tensile test. In this graph, every sample showed the own stress-strain curve distribution from the surface to core layer on each 50 μm. From this graph, every sample showed remarkably the different stress-strain curve as compared with that of the surface layer. Figure 5 and Figure 6 show the distribution of modulus and yield stress from the surface to core layer in each sample measured by Figure 4. In Figure 5, the high molecular weight sample showed higher modulus distribution than the low molecular weight samples in every layer. In HM and HW, the modulus distribution near surface showed a characteristic behavior. HW showed the highest modulus in 25 μm depth from the surface, and then the modulus was decreased about 1.5 GPa from 75 μm depth to core layer. In contrast, the modulus of HM indicated the high value from 25 to 125 μm depth, and then the value was decreased about 1.5 GPa from 175 μm to core layer. In LN and LM, these moduli showed a similar tendency with the case of HM and HW. Namely, the modulus of LM showed highest value at 25 μm depth, and the modulus of LN indicated the high value from 25 to 125 μm depth. It is considered that the difference could be due to the effect of molecular weight and molecular distribution of polypropylene. As shown in Figure 6, the results of the yield stress distribution showed a similar behavior with the results of modulus distribution.

From these results, the higher molecular weight and narrower molecular weight distribution sample showed higher modulus, yield stress and fracture toughness as compared with the other samples and these highly property samples had the highly property layer near the surface. Especially, this relationship can be observed at bulk yield stress and yield stress distribution. The high molecular weight and middle molecular weight distribution sample (HM) showed highest yield stress and modulus. In the modulus and yield stress distribution, it was found

that the HM sample had a thicker layer with high values near the surface as compared with the high molecular weight and wide molecular weight distribution sample (HW). In addition, it was found that the difference of distribution between HM and HW were not observed in the low molecular weight samples (LN and LM). In near future, the relationship between the molecular orientation, crystallinity, and mechanical properties of thin-walled PP molding parts will be investigated using X-ray deflection analysis and mechanical test.

4. Conclusion

In this research, the relationship between bulk mechanical property and mechanical property distribution of thin-wall injection molded polypropylene with different molecular weight and molecular weight distribution was investigated. The bulk mechanical properties were characterized in terms of static tensile property and fracture toughness by essential work of fracture method. The mechanical property distribution was measured by tensile test with thin-sliced dumbbell film obtained from bulk specimen. As results, it was found that the higher molecular weight and narrower molecular weight distribution sample indicated the higher modulus, yield stress, and fracture toughness as compared with the other samples. In addition, these samples had the highly property layer near the surface, it was considered that there is a correlation between these mechanical properties and the skin- core structure. The property distribution test results revealed that the highly bulk property sample had thicker highly mechanical property layer on its surface. Therefore, the value of mechanical property layer in the surface rather than the thickness of highly mechanical property layer in the surface affect the increasing bulk mechanical property.

Cite this paper

KeisukeMaeda,KojiYamada,KazushiYamada,MasayaKotaki,HiroyukiNishimura,11, (2016) The Relationship between Bulk Property and Property Distribution in Thin-Wall Injection Molded PP at Different Molecular Weight and Molecular Weight Distribution. Advances in Materials Physics and Chemistry,06,1-8. doi: 10.4236/ampc.2016.61001

References

NOTES

^*Corresponding author.