Few studies jointly investigate thermal and turbulent effects. In general, these subjects are treated separately. The purpose of this paper is to use the Immersed Boundary Method (IBM) coupled with the Virtual Physical Model (VPM) to investigate incompressible two-dimensional Newtonian flow around a heated square cylinder at constant temperature on its surface with forced convection and turbulence. The VPM model dynamically evaluates the force that the fluid exerts on the immersed surface and the thermal exchange between both in the Reynolds numbers (Re) window 40 ≤ Re ≤ 5×10 3 . For simulations of turbulence the Smagorinsky and Spalart-Allmaras models are used. The first model uses the Large Eddy Simulation (LES) methodology and is based on the local equilibrium hypothesis for small scales associated with the Boussinesq hypothesis, such that the energy injected into the spectrum of the turbulence balances the energy dissipated by convective effects. The second model uses the concept Unsteady Reynolds Averaged Navier-Stokes Equations (URANS), with only one transport equation for turbulent viscosity, being calibrated in pressure gradient layers. The goal of this work is to analyse the combination of the heat-transfer phenomena with the turbulence for the thermo-fluid-structure interaction in a square cylinder. For this, it was developed a C/C++ code that requires low computational costs in regards to memory and computer facilities. It is observed that, with the increase of the Reynolds number, an increase of the drag coefficient occurs, as well as reinforces the influence of the pressure distribution downstream of the cylinder, which is strongly influenced by the formation and detachment of vortices on the upper and lower sides of the square cylinder.
The idea of Immersed Boundary Method (IBM) was proposed by [
The first methodology uses unstructured grids to describe complex geometries, with the remeshing process for the case of deformable bodies. The second methodology used the immersed boundary method, as proposed by [
The work [
In this paper, unlike other works, it is presented the Immersed Boundary Method as a method of capturing interfaces with the Virtual Physical Model (IBM/VPM) being used to simulate the flow in two-dimensional space, with the presence of immersed geometries in incompressible fluid with forced convection around the heated square cylinder (also known as bluff bodies, with its heated surface at constant temperature, and where there is no elasticity in the immersed body). The VPM was developed by [
The VPM model has the ability to self-adjust to the flow as the force required to “stop” the fluid particles near the interface is automatically calculated, without the need to adjust variables, unlike the original method developed by [
In the IBM method, the force f is introduced into the Navier-Stokes equations to model the solid-fluid interface. Analogously, the heated body is modeled by a forcing term q added to the energy equation. Thus, the method is based on a mixed formulation with a grid for the fluid (Eulerian grid) and another for fluid-solid interface (Lagrangian grid). The bulk of this paper is to verify the applicability and potentiality of IBM/VPM to model and simulate a flow over a heated square cylinder for 40 ≤ Re ≤ 5 × 10 3 , considering the aerodynamic coefficients, this is, the drag and lift coefficients, the temperature, the Strouhal and Nusselt numbers. For the highest number of Reynolds here considered ( Re = 5 × 10 3 ) , two turbulence models are used, namely, Smagorinsky and Spalart-Allmaras models.
This paper is organized as follows. In the Section 2, it is presented the IBM methodology. Section 3 is devoted to the Virtual Physical Model used to solve the Navier-Stokes equations. The turbulence models are in Section 4. In the next Section, the numerical method is discussed. The results are in Section 6, and the concluding remarks are presented in 7.
The physical phenomena of fluid mechanics are described by a set of partial differential equations, describing the conservation of mass (continuity), momentum and energy. For the non-isothermal case, theses equations, in the context IBM/VPM, are written under the following hypotheses:
The fluid is Newtonian and incompressible with constant properties. The buoyancy term, based on the Boussinesq approximation, does not appear since we are only considering the case of forced convection;
The immersed body (heated square cylinder) is describe by the VPM model instead of by the direct imposition of the boundary conditions of velocity and temperature;
The energy generation term is neglected, because neither the effects of internal heat are considered (for example, absorption or emission radiation) nor the humidity which could be responsible for the latent heat exchange;
There is no Coriolis force nor rotation effects of the coordinate system.
The equations for Newtonian incompressible flow with forced convection can be written, in dimensionless form, as
{ ∇ ⋅ U = 0 , ∂ U ∂ t + ∇ ⋅ ( U U ) = − ∇ p + Re − 1 Δ U + f , ∂ Θ ∂ t + ∇ ⋅ ( U Θ ) = Pe − 1 Δ Θ + q , (1)
where U is the incompressible velocity field, p is the pressure, and Re is the Reynolds number. The Eulerian body-force f is used to mimic the effects of the immersed body, W, in the flow. The Reynolds number is defined by Re = U L / ν , where U, L and v are the reference length, the reference velocity, and the kinematic viscosity, respectively. Pe is the Péclet number, defined by Pe = Re × Pr , where Pr is the Prandtl number, given by Pr = c p μ / k . Here, c p is the heat capacity and k is the coefficient of thermal conductivity. The dimensonless temperature is defined by Θ = ( θ − θ 0 ) / ( θ c − θ i ) , being θ c and θ i the square cylinder temperature and the domain inlet temperature, respectively. The immersed boundary is represented by Lagrangian points, where the Lagrangian force is defined. The Eulerian and Lagrangian forces are related to each other through a regularized delta-function. The Eulerian force f , added to the momentum equation, is mathematically represented by
f ( x , t ) = ∫ ∂ Ω F ( x k , t ) δ ( x − x k ) d x k , (2)
where, x and x k are the position vectors of the Eulerian and Lagrangian points, respectively; ∂ Ω is the domain of the immersed boundary, f and F are the Eulerian and Lagrangian forces, respectively. Similarly, in the energy equation (3rd equation in system (1)), the dimensionless external heat source q, which is the mutual interaction energy between fluid and immersed boundary, is expressed as follows
q ( x , t ) = ∫ ∂ Ω Q ( x k , t ) δ ( x − x k ) d x k , (3)
where Q is the heat source on the Lagrangian point x k at the immersed boundary. In this paper, the boundary conditions of velocity and temperature are imposed by integration of the equations of momentum and energy, of the system (1). These terms are intended to model the immersed geometry by
f ( x , t ) = ∫ ∂ Ω b F ( x k , t ) δ ( x − x k ) d x k ≃ ∑ k = 1 N F ( x k , t ) D ( x − x k ) Δ s 2 , (4)
q ( x , t ) = ∫ ∂ Ω b Q ( x k , t ) δ ( x − x k ) d x k ≃ ∑ k = 1 N Q ( x k , t ) D ( x − x k ) Δ s 2 , (5)
where N is the number of Lagrangian points and Δ s is the discrete Lagrangian distance between two points. The term D ( x − x k ) is the distribution function suggested by [
D ( x − x k ) ≃ h − 2 ( g 1 [ ( x k − x i ) h − 1 ] g 1 [ ( y k − y i ) h − 1 ] ) , (6)
with
g 1 ( r ) = { g 2 ( r ) , | r | < 1 0.5 − g 2 ( 2 − | r | ) , 1 < | r | < 2 0 , | r | > 2 (7)
where h is the Euclidian grid size. The function g 2 ( r ) is given by
g 2 ( r ) = 1 8 ( 3 − 2 | r | + 1 + 4 | r | − 4 | r | 2 ) (8)
where r denotes [ ( x k − x i ) h − 1 ] or [ ( y k − y i ) h − 1 ] , and ( x i , y i ) are the coordinates of the Eulerian points. In this paper, the domain is discretized by a Cartesian grid, as shown in
The Virtual Physical Model (VPM) was proposed by [
F ( x k , t ) = ∂ U ∂ t ( x k , t ) + ∇ ( U ( x k , t ) ⋅ U ( x k , t ) ) − Re − 1 Δ U ( x k , t ) + ∇ p ( x k , t ) , (9)
where the r.h.s. parcels, from left to right, are referred to as acceleration force, inertial force, viscous force and pressure force, respectively. Similarly, for the thermal source of the fluid particle in contact with the interface, an energy balance is performed as follows:
Q ( x k , t ) = ∂ Θ ( x k , t ) ∂ t + ∇ ( U ( x k , t ) Θ ( x k , t ) ) − Pe − 1 Δ Θ ( x k , t ) , (10)
where the r.h.s. parcels, from left to right, are called local rate of change of temperature, heat dissipation rate due to convection and diffusive transport rate of the thermal energy. The terms F and Q are calculated in the interface points, through interpolation of the pressure, velocity and temperature fields, being calculated in the Lagrangian grid. After calculating Q ( x k , t ) , the Eulerian variable q ( x , t ) , in Equation (5), is obtained to finally calculate the new temperature through the 3rd equation in (1).
For the calculation of pressure and temperature derivatives at each Lagrangian point, it is necessary to obtain the pressure and temperature value on the interface point x k . For the calculation of pressure and temperature, it is necessary to use an auxiliary point, here called P, according to
The derivatives for the calculation of pressure force is performed by the finite difference method
{ ∂ p ∂ x ≃ p 2 − p 1 x 2 − x 1 ∂ p ∂ y ≃ p 4 − p 3 y 4 − y 3 (11)
The pressure and the temperature at the auxiliary point P belong to an Eulerian cell. So, to obtain the velocity, pressure and temperature, we use the following approximations (for details, see [
{ u ( x k ) ≃ ∑ i D ( x i − x k ) u ( x i ) d x d y v ( x k ) ≃ ∑ i D ( y i − y k ) v ( x i ) d x d y p ( x k ) ≃ ∑ i D ( x i − x k ) p ( x i ) d x d y p ( x k ) ≃ ∑ i D ( y i − y k ) p ( x i ) d x d y Θ ( x k ) ≃ ∑ i D ( x i − x k ) Θ ( x i ) d x d y Θ ( x k ) ≃ ∑ i D ( y i − y k ) Θ ( x i ) d x d y (12)
where the quantities u ( x k ) and v ( x k ) , in (12), represent the velocities of the fluid on the interface, taking into account the internal and external velocities to the interface on the Eulerian grid. The terms u ( x i ) , v ( x i ) , p ( x i ) and
Θ ( x i ) are, respectively, the velocities in the x- and y-direction, the pressure and temperature in the Eulerian grid which will be interpolated; the terms u ( x k ) , v ( x k ) , p ( x k ) and Θ ( x k ) , are the velocities, pressure and temperature on the auxiliary points, respectively. The derivative that composes the different terms are calculated using the second-order Lagrange polynomial.
The systems of Equations (13) and (14), in the variable f, represent the velocity and the pressure in the x- and y-direction, respectively. After the interpolation of velocity, pressure and temperature at the interface and in the auxiliary points, one determines the derivatives that constitute the terms for the calculation of the Lagrangian polynomial of the second order. Denoting the velocity or temperature components by (f), the calculation of the first and second derivatives in x and y directions, respectively, is given by
{ ∂ ϕ ∂ x = ( x i − x k ) + ( x i − x 2 ) ( x 1 − x 2 ) ( x 1 − x k ) ϕ 1 + ( x i − x k ) + ( x i − x 1 ) ( x 2 − x 1 ) ( x 2 − x k ) ϕ 2 + ( x i − x 1 ) + ( x i − x 2 ) ( x k − x 1 ) ( x k − x 2 ) ϕ k ∂ 2 ϕ ∂ x 2 = 2 ( x 1 − x 2 ) ( x 1 − x k ) ϕ 1 + 2 ( x 2 − x 1 ) ( x 2 − x k ) ϕ 2 + 2 ( x k − x 1 ) ( x k − x 2 ) ϕ k (13)
{ ∂ ϕ ∂ y = ( y i − y k ) + ( y i − y 4 ) ( y 3 − y 4 ) ( y 3 − y k ) ϕ 3 + ( y i − y k ) + ( y i − y 3 ) ( y 4 − y 3 ) ( y 4 − y k ) ϕ 4 + ( y i − y 3 ) + ( y i − y 4 ) ( y k − y 3 ) ( y k − y 4 ) ϕ k ∂ 2 ϕ ∂ y 2 = 2 ( y 3 − y 4 ) ( y 3 − y k ) ϕ 3 + 2 ( y 4 − y 3 ) ( y 4 − y k ) ϕ 4 + 2 ( y k − y 3 ) ( y k − y 4 ) ϕ k (14)
where ϕ 1 , ϕ 2 , ϕ 3 and ϕ 4 are obtained by interpolation of the nearest Eulerian variables. The coordinates of the auxiliary points (1, 2, 3 and 4) and the coordinates of the Lagrangian point x k are, respectively, the pairs ( x k , y k ) , ( x 1 , y 1 ) , ( x 2 , y 2 ) , ( x 3 , y 3 ) and ( x 4 , y 4 ) . The points 1, 2, 3 and 4 must be located outside the interface, in order to calculate the force to be independent of the flow properties in the interior. The distance between the points 1, 2, 3 and 4 is Δ x . Thus, the calculation of the inertial, viscous and pressure forces are independent of the flow inside the interface. The same process holds for the energy equation. The acceleration force, which is one of the terms of the total Lagrangian (or interface) force, is obtained by an approximation using the finite difference method, according to the expression,
∂ U ∂ t ( x k , t ) ≃ U k − U f k Δ t , (15)
where U k represents the interface velocity vector and U f k represents the velocity vector of the fluid at the same interface position. This acceleration force represents the most influential part in the calculation of the total Lagrangian force, and can be interpreted as the portion that guarantees the non-slip condition. Similarly, the time derivative for the temperature is approximated by
∂ θ k ∂ t ≃ θ k − θ f k Δ t . (16)
Another important calculation is the determination of the parameter L 2 , which provides the difference between the dimensionless velocity of the fluid at the interface and the velocity at the interface itself and its temperature. The numerical value is around 10−3, being a coherent and acceptable value, as proposed by [
L 2 ≃ ∑ k = 1 n p ( u k ( x k ) − u f k ( x k ) ) 2 + ( v k ( x k ) − v f k ( x k ) ) n p | U ∞ | 2 , (17)
L 2 ≃ ∑ k = 1 n p ( θ k ( x k ) − θ f k ( x k ) ) 2 n p | U ∞ | 2 , (18)
where ( u k , u f k ) , ( v k , v f k ) , ( θ k ) and ( θ f k ) are the components of velocities and temperatures at the interface, respectively; n p is the number of Lagrangian points in the immersed interface.
After calculating the terms of Equations (9) and (10), and obtaining the values for F and Q , the Eulerian terms for f and q are evaluated in order to obtain the distribution of the interfacial force and the thermal field. The calculation process is performed as follows:
f ( x i ) ≃ ∑ k D i , j ( x i − x k ) F ( x k ) Δ s ( x k ) , (19)
q ( x i ) ≃ ∑ k D i , j ( x i − x k ) Q ( x k ) Δ s ( x k ) , (20)
where f ( x i ) is the force on each Eulerian node, while F ( x k ) is the force of each Lagrangian node being distributed to the Eulerian nodes.
The average distance between two adjacent points is represented by Δ s ( x k ) and D i , j is a distribution function. In Equation (20), it is shown the thermal source term, q ( x i ) , for each Eulerian node, due to the presence of the heated immersed body, and Q ( x k ) , the thermal source in each Lagrangian node, being distributed to the Eulerian nodes, thus forming an Eulerian thermal field, that acts on the particles near the border.
In addition to laminar regime flow, we have also simulated (turbulent) flow for Reynolds numbers going up to 5 × 10 3 . Thus, it is necessary to use turbulence models to close the Navier-Stokes equations. Two models were implemented, namely the Smagorinsky model, with LES (Large Eddy Simulation) methodology, and the Spalart-Allmaras model (S-A), with URANS model (Unsteady Reynold Averange Navier-Stokes) (for further details, see [
The URANS model is used to refer to RANS (Reynolds Averaged Navier-Stokes), where in this model, the dependent variables of the Navier-Stokes equation are decomposed into filtered components and floating components, and then all terms are filtered. In the LES methodology the largest turbulence structures (eddy structures) are solved by filtered equations and only the smallest structures are modeled, since they are (statistically) homogeneous and isotropic. The scale of the small structures is calculated by the size of the grid used for the solution of the Navier-Stokes filtered equations. In other words, the width of the filter becomes a function of the grid. In this way, turbulent structures that are smaller than the grid solution are modeled by the so-called sub-grid models.
The Smagorinsky sub-grid model [
ν t = ( C s l ) 2 2 S ¯ i j S ¯ i j , (21)
where C S = 0.18 is the Smagorinsky constant and l = Δ x Δ y is the length of the sub-grid scale.
The Spalart-Allmaras model is a one-equation model that solves the transport equation for the kinematic eddy turbulent viscosity [
The equation for the turbulent viscosity is constructed using mainly flow empirical considerations, dimensional analysis and Galileo’s principle of relativity. The model uses a working variable, ν ˜ , given by the following transport equation:
∂ ν ˜ ∂ t + ∂ ∂ x j ( u j ν ˜ ) = c b 1 ( 1 − f t 2 ) S ˜ ν ˜ + 1 σ [ ∂ ∂ x j ( ( ν + ν ˜ ) ∂ ν ˜ ∂ x j ) + c b 2 ∂ ν ˜ ∂ x j ∂ ν ˜ ∂ x j ] − [ c w f w − c b 1 k 2 f t 2 ] [ ν ˜ d w ] − f t 1 Δ U 2 , (22)
where the terms on the right side, respectively, represent: the production of turbulent viscosity, the molecular and turbulent diffusion of ν ˜ , the dissipation of ν ˜ , the destruction of ν ˜ , which reduces the turbulent viscosity near the wall and, finally, the terms that model the transition effects, indicated by sub-index t. The turbulence viscosity, ν t , is calculated from the auxiliary variable of the Spalart-Allmaras model and damped by the function f v 1 along the wall, and is given by
ν t = ν ˜ f v 1 , (23)
where
f v 1 = χ 3 χ 3 + C v 1 3 , (24)
with
χ ≡ ν ˜ ν . (25)
The production term in the transport Equation (22) also needs a correction, which is performed by replacing the parameter S with a modified variable S ˜ , which also depends on the influence of a damping function f v 2 . Thus, S ˜ is defined by
S ˜ ≡ S + ν ˜ ( k d w ) 2 f v 2 , (26)
where d w is the distance to the nearest wall, and S is the modulus of the strain rate given by
S = 2 S ¯ i j S ¯ i j . (27)
The term of destruction originally formulated by [
f w = g ( 1 + c w 3 6 g 6 + c w 3 6 ) 1 / 6 , (28)
g = r + c w 2 ( r 6 − r ) , (29)
with
r ≡ ν ˜ S ˜ k 2 d w 2 . (30)
(Here, k is an empirical constant of the model.) The influence of these terms allows the control of the transition in two different aspects: in the maintenance of the laminar flow in the desired regions or beginning the transition region. The control is performed with the addition of a source term, being controlled by the function f t 1 and a reduction in the production term of the turbulent viscosity controlled by the function f t 2 , being defined as follows
f t 1 = c t 1 g t exp ( − c t 2 ω t 2 Δ U 2 [ d w 2 + g t 2 d t 2 ] ) , (31)
f t 2 = c t 3 exp ( − c t 4 exp χ 2 ) , (32)
where d t is the distance to the start point of the transition, ω t is the vorticity at the point of transition of the boundary-layer, and Δ U is the norm of the velocity difference between the flow and the transition point. The function g t is defined by m i n { 0.1 ; Δ U / ( ω Δ x t ) } , where Δ x t is the size of the grid along the wall in the transition region. These terms were neglected, as the simulations were only performed for fully developed turbulence regimes. The other constants of the model are σ = 2 / 3 , c b 1 = 0.1355 , c b 2 = 0.622 , k = 0.41 ,
c w 1 = c b 1 k 2 + 1 + c b 2 σ , c w 2 = 0.3 , c w 3 = 2 and c v 1 = 7.1 . These constants were determined empirically.
The mean temperature field Θ ¯ is governed by
∂ Θ ¯ ∂ t + ∂ ( u ¯ j Θ ¯ ) ∂ x j = ∂ ∂ x j [ ( α + α t ) ( ∂ Θ ¯ ∂ x j ) ] , (33)
where α t is the turbulent diffusion coefficient, being determined by
α t = ν t Pr t , (34)
where Pr t is the Prandtl number, which controls the magnitude of the mean turbulent diffusion. The turbulent thermal diffusivity value is 0.9 in all simulations.
In the order to validate our code, simulations with a single heated square cylinder were compared with the results found in the literature. To mimic free boundary conditions, it was considered L x = 55 d and width L y = 30 d . The heated square cylinder was placed at x = 16.5 d and y = 15 d , in order to minimize the influence of the boundaries. The grid resolution for these simulations was 318 × 164 points, a non-uniform grid was used to better capture the effects with a total of 201 Lagrangian grid points inside the immersed body. The 2nd and 3rd equations in (1) were discretized 1) in space, using the method of centered finite difference, and 2) in time, by the second order Adams-Bashforth scheme, and solved in the two-dimensional domain together with the fractional step method for calculating the iterative time step and the coupling between pressure, velocity and temperature, respectively. The discretized expression for the pressure correction results in a linear system that was solved using the MSIP (Modified Strongly Implicit Procedure Method), developed in [
u ¯ i n + 1 − u i n Δ t + [ ∂ ∂ x j ( u i n u j n ) ] = − 1 ρ ∂ p n + 1 ∂ x i + ∂ ∂ x j [ ( ν + ν t ) ( ∂ u i n ∂ x j + ∂ u j n ∂ x i ) ] + f i n (35)
1 Δ t ∂ u ¯ i n + 1 ∂ x i = 1 ρ ∂ 2 p ′ n + 1 ∂ x j ∂ x j , (36)
u i n + 1 = u ¯ i n + 1 − Δ t ρ ∂ p ′ n + 1 ∂ x i , (37)
p ′ n + 1 = p n + 1 − p n , (38)
θ i , j n + 1 − θ i , j n Δ t + [ u i + 1, j θ i + 1, j + θ i , j 2 Δ x − u i ,, j θ i , j + θ i − 1, j 2 Δ x ] + [ v i + 1, j θ i + 1, j + θ i , j 2 Δ y − v i ,, j θ i , j + θ i − 1, j 2 Δ y ] = Pe − 1 ( [ θ i + 1, j − θ i , j Δ x − θ i , j − θ i − j Δ x ] 1 Δ x + [ θ i + 1, j − θ i , j Δ y − θ i , j − θ i − j Δ y ] 1 Δ y ) + q i , j , (39)
where the calculation of the force field on the interface, and the solution of the momentum and energy equations are performed explicitly. The computational domain is shown in the schematic illustration of
The grid is uniform in the region of the heated square cylinder, maintaining a minimum number of 30 grid inside. The time step used in the calculation process is in the range 1.0 × 10 − 6 s to 1.0 × 10 − 4 s , which is dynamically calculated by the Courant-Friedrichs-Lewy condition (CFL condition):
CFL j = max ( | u | + c ) [ x j − 0.5 , x j + 0.5 ] × Δ t Δ x j , (40)
which is necessary for the explicit solution over time. To avoid numerical problems, the maximum ratio of 3% grid expansion was employed in these regions in both directions. In the present paper, the ratio between Lagrangian and Eulerian grid size was maintained at 0.98.
In this section, the heat-transfer by forced convection and turbulence problems are simulated using the IBM/VPM method. The results of the simulations are compared with previous results. Isothermal IBM/VPM conditions are implemented and studied. The Reynolds numbers are 40, 50, 100, 500, and 5000. The Prandtl number is fixed at 0.7 in all cases. The staggered grid arrangement is applied in all cases. The square cylinder D is 1, with the center positioned at 16.5d from the domain entry and at 15d from top domain wall, and the free-stream velocity U ∞ . The computational domain is 30 d × 55 d , with the center of the cylinder located at ( 16.5 d ,16.5 d ) . These dimensions were determined numerically in order to minimize the influence of the domain on the flow around the square cylinder and, at the same time, to minimize the total number of nodes required. Newman boundary conditions were used.
The boundary condition were prescribed as follow: 1) uniform flow with velocity U ∞ , pressure p = 0 , and temperature Θ input = 0 at the entrance of the domain (left side); 2) flow fully developed in the output ( ∂ u / ∂ x = 0 , ∂ Θ / / ∂ x = 0 ) ; 3) condition of symmetries at the upper and lower boundaries ( ∂ u / ∂ y = v = 0 ) , ( ∂ Θ / ∂ y = 0 ) . Concerning the initial condition, u = v = 0 , at t = 0 (time), for the entire computational domain. The square cylinder is maintained at a constant dimensionless temperature equal to 1, i.e. Θ c = 1 , while the fluid has an initial temperature equal to zero ( Θ f = 0 ) . Although the boundary condition at the output is not a reflexive condition, the simulation results successfully corroborate the formation of large (vortex) structures outside the domain without any reflection. The current pressure limit conditions at the inlet and outlet limits are imposed to be consistent with the equations for velocities due to the arrangement of the staggered grid.
the vortices for the higher Reynolds numbers is clearly observed, whereas, for Re = 40, the flow is stable.
The time evolution of the drag, C D , and lift, C l , coefficients are shown in
In
In these figures, the vortex detachment is observed in both cases (time » 70). After 1.7 million iterations (»4 hours of CPU time), the flow is fully developed (at low computational cost). In
Contrary to what was observed in
and the lift coefficient, C l , in the square cylinder, varies in time, i.e. occur amplitude variations. This is a consequence of the periodic detachment of vortices on the upper and lower surfaces of the square cylinder. The lift coefficient, C l , also presents oscillation, that is, there is buoyancy in the flow. In
but a physical consequence caused by the turbulence. This type of flow is unstable and contains fluctuations that are dependent on time and position in space. These disturbances, shown in
In
In
In
Authors | Re = 40 | Re = 50 | Re = 100 | Re = 500 | Re = 5000 |
---|---|---|---|---|---|
Present work | 1.34 | 1.36 | 1.36 | 1.38 | 1.57 |
Breuer [ | - | 1.48 | 1.37 | - | - |
Perumal et al. [ | - | 1.21 | 1.80 | - | - |
The mean Nusselt numbers are presented in
N u ¯ = c × Re D m × Pr 1 / 3 . (41)
The immersed boundary method coupled with the virtual physical model was used to simulate incompressible two-dimensional flows around a heated square cylinder at constant temperature on its surface. In order to validate the code, the works [
In all simulations, the results show that the influence of the surface of the heated body immersed in the flow increases as the Reynolds number increases.
Authors | Re = 40 | Re = 50 | Re = 100 | Re = 500 | Re = 5000 |
---|---|---|---|---|---|
Present work | - | 5.18 | 6.13 | 26.67 | |
Vieira [ | - | - | - | 8.10 | - |
For the temporal discretization, the second order Adams-Bashforth scheme was used together with the spatial centered scheme. A turbulence model was also used for the energy transfer process between the largest and smallest turbulent scales.
For future work, it is planned to extend this work to more complex geometries, more precisely, to simulate tandem cylinder configurations in stationary and non-stationary cases. This will allow investigating mixed convection (natural and forced).
SG and RS acknowledge the partial support by CMUP (UID/MAT/ 00144/2013), which is funded by FCT (Portugal) with national (MCTES) and European structural funds (FEDER), under the partnership agreement PT2020-ext. to 2018. RS acknowledges the financial support by CAPES (Brazil). SG acknowledges the Project STRIDE-NORTE-01-0145-FEDER-000033, funded by ERDF NORTE 2020. The authors thank Virtual Hydrodynamics Laboratory of the Institute of Mechanical Engineering of the Federal University of Itajubá (Brazil) for the computer facilities.
Santos, R.D.C., Gama, S.M.A. and Camacho, R.G.R. (2018) Two-Dimensional Simulation of the Navier-Stokes Equations for Laminar and Turbulent Flow around a Heated Square Cylinder with Forced Convection. Applied Mathematics, 9, 291-312. https://doi.org/10.4236/am.2018.93023