Seeking to use an increasingly clean and sustainable energy matrix, the use of biomass derivatives becomes an increasingly present alternative. Among the processes that can be used to generate higher added value products from biomass, the gasification process is highlighted. The irregular and spherical shape of the biomass particles inserted in the bed make this process difficult, however, and it is necessary to add an inert material (usually sand), forming a polydisperse bed filled with a binary mixture, but the biomass/sand is extremely important for the fluidization process to occur. Therefore, the present work had the objective of determining the fluidization curves of a binary mixture of sand and fodder turnip, which is formed by 10%, 30%, 50%, 70% and 90% of biomass in its volume. The fluidization of the Raphanus sativus L. husk fluidized up to a 70% biomass ratio in the blend, increasing the yield of the system and providing a viable and sustainable alternative for the application of biomass in biorefinery processes.
The search for the substitution of fuels that can replace the energy coming from fossil fuels has given the sources of renewable energy a prominent role in the energetic scene. Fossil fuels, finite and highly polluting, are losing ground to the energy generated from the sun, the winds and biomass [
Still according to Santos [
The use of the chemical and energy potential of biomass can be done through chemical, biochemical or thermochemical routes. Within the thermochemical routes, the conversion of the biomass into bioelectricity becomes extremely efficient through the combustion of it in fluidized bed reactors. Fluidization allows a greater homogenization of temperature in the reactor by increasing the contact surface between the upward fluid in the bed and the fuel to be fluidized, generating high rates of heat transfer and mass [
One of the obstacles to the use of biomass in fluidization processes, according to Genher [
The fluidization process of this binary mixture is influenced, among other things, by the proportion of biomass, considering that a mixture containing large amounts of biomass tends to present greater fluidization difficulties, forming preferential paths in the bed or causing segregation of the parts of the mixture [
Through this study, it is possible to verify the possibility of using Raphanus sativus L. in gasification processes as well as to optimize the feed rate of the fluidized bed reactor.
Fluidization is a necessary instrument for gasification of biomass, a process by which a solid fuel is transformed into a gaseous fuel, which can be commercialized for the generation of bioproducts or as a source of heat, thus offering a new alternative to the energy matrix.
A legume belonging to the Brassicaceae family, Raphanus sativus L. is an oilseed commonly used in green manuring and crop rotation in the central-west, south and southeast regions of Brazil [
The Raphanus sativus L. can be visualized in
The biomass used in the experiment was provided by the State University of Rio Grande do Sul, located in Três Passos, which originates from the experimental cultivation area of the Agronomy course. As standout characteristics, the cultivar presents a high capacity of cycling of nutrients such as nitrogen and phosphorus, and then, the capacity to develop in soils considered poor for other crops [
The Raphanus sativus L. husk was cultivated and supplied by the Universidade Estadual do Rio Grande do Sul in Três Passos/RS unit. The Raphanus sativus L. was placed in a stove to remove moisture at a temperature of 105°C for a period of 8 hours in constant homogenization.
After this step, was used, in the Laboratory of Characterization and Valorization of Materials (LCVMAT), of the Universidade do Vale do Rio dos Sinos, the knife mill of brand SEIBT, type MGHS 270 A, With a 4 mm sieve, allowing the biomass to be reduced in size (
After the milling process, the specific mass of the biomass as well as the sand, used as an inert material during the fluidization, was determined.
In the determination of the specific mass, according to norm NP EM 1097-6, the pycnometry with water was performed. By this analysis, it was possible to obtain the actual specific mass of the sand used in the binary mixture; however, due to the low density of the biomass particles, it was not possible to obtain its actual specific mass values through this test.
Due to the impossibility of determining the actual specific mass of the biomass via pycnometer with water, the analysis was changed for helium gas pycnometer. The pycnometer used was Micromeritics, model AccuPcy II 13 of the LCVMAT.
To measure the apparent density of the material, the mass of material needed to fill the bed up to the height (H) of 94 mm was measured, this value being also corresponding to the bed diameter (D). In this way, the ratio H/D ≈ 1. For the preparation of the samples was defined as standard volume 2.60 × 10−3 m³, this being the standard volume used in the preparation of the samples. The ratio obtained between the mass of the material and its apparent volume determined the apparent specific mass of the material.
With the apparent density of the biomass and the apparent density of the sand, the biomass and sand mixtures were made in different volumetric proportions, containing 10%, 30%, 50%, 70% and 90% of biomass, being complemented by the addition of inert material. The mixtures were sent to the fluidization bed (
The fluidization bed consists of a cylindrical acrylic tube that has an internal diameter of 94 mm and a wall thickness of 3 mm. At the bottom of the bed, there is a 100 mm stainless steel tube. This is called a distributor, whose purpose is to distribute the upward flow of fluid uniformly throughout the cross-sectional area of the bed. Below the distributor is a semiconductor in which the fluid used is inflated in the bed. The fluid used in the experiment was air.
At the ends of the distributor, there are metallic screens; the one located at the lower end serves to support the glass beads, randomly arranged in the dispenser, while the screen at the top of the dispenser serves to support the material to be fluidized, which comes to compose the bed.
For the measurement of the flow of the compressed air inflated in the bed a meter, which brand is IFM, type SD6050, which measures pressure in the range of 0.2 to 75 Nm³/h, with an accuracy of ±1.5% and analogue signal output in the range of 4 to 20 mA.
The pressure difference was used to determine the load loss occurring during the passage of fluid through the bed. For this, pressure is drawn from the fluid inflated in the bed, before passing through the distributor, and the fluid after passing through the column of fluidized material. This second pressure take-off occurs through an orifice located above the column of the material composing the bed.
For this pressure take-off was used the equipment, which brand is NOVUS, type HUBA 699, With adjustable measuring range between 0 to 16 mbar, 0 to 25 mbar e 0 to 50 mbar, as well as a data collection board, type Fieldlogger. The data were collected simultaneously at each second in real time through software, allowing analysis of the behavior of the pressure loss according to the increase of fluid flow in the bed.
After the mixture of biomass and sand was inserted in the bed, the air flow was increased to homogenize. After the airflow was interrupted, the bed was put back in its initial position for the experiment to be performed. The air flow was increased manually, during the increase of the air flow, the expansion of the bed, and after reaching a limit, it was noticed the appearance of air bubbles on the surface of the bed.
The actual and apparent densities of the sand and forage turnip obtained can be seen in
It was noted that both the specific mass and apparent density of the Raphanus sativus L. are lower than that of Pinus and Eucalyptus. The apparent density interferes with the mass of the biomass present in the mixture, which in turn will impact on the fluidization process of mixtures with a large amount of biomass, mainly in the formation of preferred paths in the segregation of the mixture. The volumetric proportions of biomass in the mixture were chosen to cover two extreme scenarios, the first one in which the amount of biomass is small, being only 10%, and the second in which the amount of biomass is the majority, being 90%. Thus, a standard volume of was established, and using the apparent density of the biomass and the sand, the masses were calculated so that the mixtures with the established proportions were obtained.
The mass fractions (χ Raphanus Sativus L.) present in each fluidized mixture can be seen in
After the fluidizations were carried out, the load loss curves (Δpmbar) as a function of the upflow fluid flow rate (Nm³/h) were obtained by collecting the data in real time. After the conversion of the flow unit, the curve describing the load loss as a function of the inflow velocity of the upward fluid in the bed was obtained. To facilitate the presentation of results a curve identification code was established:
Where XX corresponds to the volumetric percentage of biomass in the mixture,
Density | [g/cm³] | Reference |
---|---|---|
ρRaphanus Sativus L Husk | 0.723 | Author |
ρsand | 2.61 | Author |
ρap. Raphanus Sativus L | 0.116 | Author |
ρap.sand | 1.554 | Author |
ρeucalyptus | 1.386 | Genehr |
ρpinus | 1.271 | Genehr |
ρap.eucalyptus | 0.93 | Genehr |
ρap.pinus | 0.77 | Genehr |
% Volumetric of biomass | Mass | % Mass | |
---|---|---|---|
sand (g) | Raphanus sativus L. husk (g) | χ Raphanus Sativus L. | |
10% | 912.36 | 7.54 | 1% |
30% | 709.61 | 22.62 | 3% |
50% | 506.87 | 37.71 | 7% |
70% | 304.12 | 52.79 | 15% |
90% | 101.37 | 67.87 | 40% |
assuming the values of 10, 30, 50, 70 or 90, and Y will assume the letter F, indicating the fluidization process, or the letter D, indicating the process of defluidization.
The fluidization and defluidization curves are shown in the graphs of
It is possible to observe, after the data analysis, that the increase of the ratio of Raphanus sativus L. husk causes the decrease in the load loss, in contrast, increasing both the apparent fluidization velocity and the minimum fluidization velocity (
The Ufa is determined experimentally by the point of greatest loss of charge during the fluidization process. Upon reaching the velocity corresponding to the maximum loss of charge the particles of the bed start to move and the bed then passes from the fixed to the fluidized state.
During the defluidization process, the Umf occurs at the intersection between the line at which the pressure is stabilized, and the fluidization curve of the immersing component of the blend.
The reduction of the load loss in the mixtures with greater amount of biomass can be understood by the decrease in the total mass of the mixture, due to the lower density of the biomass compared to the sand used, thus the drag force ne-
cessary to compensate the weight force of the particles becomes smaller, which causes the air load loss to be smaller. On the other hand, the higher biomass increase in the mixture favors the appearance of preferential paths, which, in addi- tion to contributing to the reduction of the load loss, causes an increase in both the apparent fluidization velocity and the minimum fluidization velocity (
The increase in airflow, however, causes the entrainment of the bed particles, causing a large amount of biomass to be lost. The irregular and low sphericity form of the biomass also contributes to the segregation processes of the bed mix occurring.
In the process of fluidization containing Pinus and Eucalyptus, Genehr [
Increasing the proportion of Raphanus sativus L. in the bed of a fluidized bed
ꭓ Raphanus Sativus L husk | Ufa [m/s] | ∆pressure [mbar] | Umf [m/s] | ∆pressure [mbar] |
---|---|---|---|---|
1% | 0.0262 | 10.597 | 0.0280 | 9.444 |
3% | 0.0319 | 8.197 | 0.0279 | 7.528 |
7% | 0.0303 | 5.513 | 0.0386 | 5.529 |
15% | 0.0454 | 4.980 | 0.0723 | 2.603 |
40% | 0.1469 | 2.021 | 0.1740 | 1.436 |
reactor causes the formation of small-preferred paths, which provide for the decrease of bed load loss.
The increase of the flow of the fluid causes the biomass particles to be dragged out of the bed, causing the loss of biomass, consequently reducing the efficiency of the system. This fact is mainly due to the large difference in the specific mass of the sand particles and the Raphanus sativus L., as well as the low spherical shape of the biomass particles, which favors their drag.
Finally, for the use of the Raphanus sativus L. presented in fluidized bed reactors, it is necessary to control the proportion of biomass and inert material, and in the experiment, the mixture containing the proportion of 50% sand and 50% of Raphanus sativus L. has not caused a significant change in the fluid pressure drop, which indicates the absence of preferred paths, thus providing an interesting proportion for use on a larger scale.
Gomes, L., Sgorla, V., Auler, A., Villares, M., Vuelma, J., Zinani, F. and Santos, F. (2017) Preliminary Study of Fluidization Curves in Polydisperse Beds Formed by a Binary Mixture of Raphanus sativus L. Husk and Sand. Open Access Library Journal, 4: e3713. https://doi.org/10.4236/oalib.1103713