This study introduces a new design of planar antenna array for ISM band applications at 2.4 GHz. This prototype is switched beam antenna, namely planar antenna with four meandered slotted triangular elements (PAFMSTE), which is proposed for wireless indoor applications. The Base Station (BS) equipped with this planar antenna is preferred to be at the center position on the room ceiling to cover all sectors of the room. It is designed to use four directional triangular elements arranged to form a square planar antenna array. The PAFMSTE is used to obtain optimal directivity in four directions in azimuth plane with 3 dB beamwidth of 90 ° at a specific orientation of 30 ° in elevation plane. Switched parasitic technique is used to enable PAFMSTE to steer a directional beam through four locations by using four PIN diodes switches. The High Frequency Structure Simulator (HFSS) is used as an efficient simulation tool to optimize the performance of the PAFMSTE antenna. The fabrication and measurements of the PAFMSTE antenna are introduced. The proposed antenna enable radio positioning via Angle of Arrival (AOA) information collected from nearby devices. Then, the Cramér-Rao Bound (CRB) is presented for AOA estimation using identically and equally spaced antenna elements. The CRB depends on the directivity, where the maximum values of CRB are 1.35 × 10 -3 and 8 × 10 -3 at HPBW of 60 ° and 90 °, respectively.
Smart antenna technology is becoming one of the most effective utilities for improving performance and available spectrum usage demanded by the rapid growing market of wireless communications [
A switched-beam system is the simplest smart antenna technique. Such an antenna system detects signal strength, chooses from one of several predetermined fixed beams, and switches from one beam to another as the node moves throughout the sector [
This paper presents a new switched beam antenna designed to address the challenges of indoor positioning and suitable for Angle-of-arrival (AOA) estimation. Among the many solutions proposed, systems based on AOA estimation have several qualities that make them attractive to a wide range of applications. Additionally, angle-based positioning only requires measurements from two anchor nodes [
A Base Station (BS) equipped with a switched-beam directional antenna can be optimized for installation on the ceiling of any large indoor space as shown in
In this scenario, a new electronically beam steerable microstrip patch antenna is presented, which can be mounted in ceilings for indoor wireless network applications. The proposed antenna is reconfigurable by using four PIN diodes switches. A planar antenna with four meandered slotted triangular elements (PAFMSTE) is proposed to cover the room with radiation pattern diversity and high reliability. The radiation pattern direction of PAFMSTE is in the desired direction of 30˚ in elevation plane with 3dB beamwidth of 90˚ in azimuth plane, which covers almost half of the whole solid steradian.
Design and performing the simulation analysis of the proposed PAFMSTE with the FR-4 epoxy PCB substrate of dimensions 69 × 69 × 1.6 mm3 is presented. This antenna is designed to operate at 2.4 GHz ISM band and a 50 Ω microstrip feed line is used. The presented smart antenna is based on 2D planar antenna with high coverage area.
The design of the PAFMSTE antenna is optimized using the finite element method (FEM) utilized in Ansoft’s High Frequency Structure Simulator HFSS 10.1.2 [
This antenna support directional communication to enable spacial reusability to mitigate multipath propagation. The system can locate a target by estimating AOA of the incoming messages in the azimuth plane, which relies on the received signal strength indicator (RSSI) of the attached base station. Then, the Cramér-Rao Bound (CRB) is presented for AOA estimation using identically and equally spaced antenna elements, where the design parameters are the number of antenna elements and their directivity [
The square patch antenna is divided into four identical isosceles triangular antennas and each triangular antenna covers each sector of the room. The single beams should exhibits a directional pattern to reduce the interferences and enable spatial reusability. To meet the design requirements, the PAFMSTE has been identified as a suitable geometry for the antenna implementation as shown in
The PAFMSTE consists of four equal size meandered slotted triangular patch elements situated on top of a square printed circuit board (PCB) and with a ground plane located on the bottom side of the PCB forming the well known parallel topology. Thus, the beam-steering can be carried out equally through four directions in azimuth plane, where the beam orientation and coverage can be controlled by four PIN diodes varying
switches. Each direction state has one PIN diode ON and the others are OFF.
Each isosceles triangular element of the patch antenna has two meandered edges with meandered slot. To obtain the optimal configuration, the patch antenna was optimized with the steepest gradient optimization procedure. By extending the meandered edges of the staircase triangular patch antenna, it becomes equilateral triangular microstrip patch antenna with length of 62.4 mm. The resonance frequency of the equilateral triangular microstrip patch antenna depends on substrate thickness, relative dielectric constant, side length of the equilateral triangle, and the location of the feed point [
Loading the slot in the radiating triangular patch antenna can cause meandering of the excited patch surface current paths and result in lowering the antenna fundamental resonant frequency, which corresponds to reducing antenna size as compared to the conventional triangular patch antenna at the same operating frequency [
RF PIN diodes can be used as switches of the reconfigurable radiation pattern antennas. At RF frequencies the MPP4204 PIN diode behaves as a variable resistor, but with slightly more complicated equivalent circuit models for the ON/OFF states, as shown in
first one is L and the second one is either the RS for the ON state or the parallel combination of RP and CT for the OFF state, as shown in
The designed antenna was fabricated on the FR-4 epoxy PCB substrate with a thickness of 1.6 mm, a dielectric constant of 4.4, and a dielectric loss tangent of 0.02 [
Simulation and measurements were performed for the patch antenna with one element fed by a 50 Ω coaxial feed, while the remaining elements open-circuited. The simulated and measured reflection coefficient as a function of frequency was obtained as shown in
Each isosceles triangular patch antenna exhibits a mono-lobe radiation pattern characterized by half power beamwidth in elevation plane of about 60˚ and half power beamwidth in azimuth plane of about 90˚, which meets the requirements of having a cumulative radiation with an (approximately) uniform coverage.
The simulated far field radiation patterns in the elevation plane and the azimuth plane are illustrated in
good agreement between the measurement and the simulation results in the region of interest from 0˚ to 90˚ are clearly observed. However the holding ground plane in the measuring setup reduced the back radiation compared with the simulated results.
On the other hand, combining the four patches by shorting the four PIN diodes switches to the coaxial feeding point produces nearly omnidirectional pattern as shown in
Consider a BS equipped with N selectable antenna beams. The system is designed to estimate the AOA of the messages transmitted by a target node relative to azimuth plane. To this purpose, the BS measures the Received Signal Strength (RSS) on each triangle element i.
The RSS of each element is function of the gain of each element in the direction of the target Gi(θ), the RF power arriving at the BS is Prx, and a random component that
models the noise is ni. Note that each measurement RSSi is a random variable that depends on the unknown parameters θ and Prx.
The Prx value varies with the transmission power used by the target and with the random attenuation introduced by the radio channel. Since Prx does not carry information on θ, its contribution can be removed by considering the RSSi,j differences between two faces i and j and nij = ni ? nj [
The PAFMSTE system is built with N = 4 identical and equally spaced antenna elements, and if the target’s distance is much larger than distance between the faces, the gains can be expressed as Gi(θ) = G(θ?2iπ/N).
The analysis adopts the Fisher information (F) to evaluate the accuracy of a generic AOA estimation algorithm in relation to some important design parameters. The value F measures the amount of information that a random variable carries about an unknown parameter. In the case discussed, the random variables are the RSSi,j values, while the parameter to estimate is θ. The Fisher information is:
where ƒij (RSSij; θ) is the probability density function that describes the measurements RSSij. Assuming independent and identically distributed noise components nij is the zero-mean additive Gaussian noise. The Fisher information F(θ) expresses the theoretical limit achievable when estimating θ. If θ' is an unbiased estimator for θ, the inverse of F(θ) bounds the minimum variance of the estimation error:
The inequality Equation (2), known as the Cramer-Rao bound (CRB), is a limit that applies to any estimator that uses measurements RSSij to compute θ. The Fisher information and the CRB depend on the gains Gi of the antennas used in the system. The gain of each antenna element [
Radiation pattern is maximum at φi = φmax = 30˚ and θi = θmax = iπ/2 in elevation and azimuth plane, respectively. The larger values of the exponent m correspond to more directive antennas.
The CRB for the estimated unbiased θ' can be expressed as [
where σrss is the RSS measurement variance. The CRBs at HPBW of 60˚ and 90˚ are illustrated in
This paper introduced a new smart antenna, namely PAFMSTE based on the concept of switched beam capable of operating for indoor mobile wireless systems in the 2.4 GHz band. The PAFMSTE achieves optimal directivity in four directions in azimuth plane with 3 dB beamwidth of 90˚ at a specific orientation of 30˚ in elevation plane to cover all sectors of the room. It is based on 2D planar antenna instead of 3D arrangement. The design approach has been described in details with the PIN diode switches and their HFSS models. The simulated and measured results are described. The proposed solution also showed the AOA estimation of the target node by using the Fisher infor-
mation theory and the CRB. The CRB exhibits good results, where it has maximum values of 1.35 × 10−3 and 8 × 10−3 at HPBW of 60˚ and 90˚, respectively. In the future studies, the number of antenna elements will be increased with decreasing the HPBW of each antenna element to improve the CRB values.
Elsamnty, R., Attiya, A.M., Abdallah, E.A.F. and Ammar, A.H. (2016) A 2.4 GHz Switched Beam Antenna for Indoor Applications Using Angle of Arrival Estimation. Open Journal of Antennas and Propagation, 4, 109-118. http://dx.doi.org/10.4236/ojapr.2016.43008