A hydrodynamic model of thin, laminar, gravity-driven, wavy-film flow over a vertical plate was considered. To make advantage of the cyclic boundary conditions and due to the nature of the wavy flow, a solution based on a Fourier series was implemented. Two representative cases of practical importance were studied; Re = 25, Re = 100. This range of Reynolds numbers is of the most practical importance in the process industry. Multiple solutions were obtained. Most of these solutions are mathematically correct but physically are not. It is observed that realistic wave profiles are always obtained once we approach the Froude number corresponding to thin film.
Thin films flowing down vertical surfaces have been extensively studied because of their common occurrence in a variety of engineering applications. The transport properties typical of thin-film flows are especially suited to applications in industrial process equipment. The efficient heatand mass-transfer characteristics of the film are primarily the result of the thinness of the film and are further enhanced by the presence of waves on the liquidvapor interface.
Gravity is the driving force which creates the film flow and gives rise to the term “falling film”. In addition to the gravity force, the falling film is acted upon by an opposing shear force between the film and the solid surface and by a second shear force caused by the difference in viscosity of the fluid and the gases at the interface. The gravity effect on the falling film is expressed in terms of the Froude number, while the fluid flow rate is expressed in terms of the film Reynolds number.
Casual observation of a thin film on a vertical surface reveals certain important characteristics of the flow. The most obvious feature is the essential unsteadiness of the motion. With disturbances normally present in laboratory situations waves will develop on the liquid-vapor interface. For disturbances with a dominant perturbing frequency and a limited side-band width, a finite-amplitude, wavy-flow state can be observed. In this situation, constant wave amplitude is approached asymptotically with flow length as nonlinear interaction of wave modes results in an equilibrium condition. In other, more common situations, the presence of a wide spectrum of perturbing disturbances precludes the possibility of an observable stable equilibrium state. However, it does appear that developing flow characteristics can be satisfactorily described for much of the flow length by these asymptotic states Hirshburg and Florschuetz [
In the literature, several techniques have been attempted to solve the wavy film motion (Dukler, [
1) The above brief review suggests that wavy motion in a falling liquid film enhances heat or mass transfer relative to the case of smooth laminar motion and despite progress made in recent years; significant gaps exist in understanding and modeling the falling films.
2) The objective of this work is to predict the wavy film flow profile using a hybrid analytical-numerical method. The solutions are valid for low and moderate Reynolds numbers regimes where the linear stability and the asymptotic finite-amplitude wave analysis of equilibrium flow states are still valid. This range of Reynold’s numbers is of the most practical importance in the process industry.
For two-dimensional laminar flow, the governing equations for constant fluid properties in the coordinate system shown in
The associated boundary conditions are
1) No slip and no penetration on the wall;
2) Negligible shear stress and balanced normal forces on the interface;
3) Specified global mean flow rate;
4) A permanent wave transformation can be employed. This is because we are studying the asymptotic periodic wave state.
The free surface boundary conditions for negligible shear stress and balanced normal forces can be expressed respectively after some manipulations as
and
From the continuity equation
Since the film thickness is very small compared to the film length in the x-direction, an order of magnitude analysis combines Equations (1)-(3) and (6) such that:
and the boundary conditions become:
Udea and Tanaka [
where is the cross-sectional mean velocity defined as
Plugging Equation (11) and the boundary conditions Equations (9) and (10) into Equation (7) and making all necessary partial derivatives, we obtain
.(13)
For periodic wave states, there exists a permanent wave transformation variable where c is the wave velocity. The wave amplitude can be described by
where, is the mean film thickness over the wavelength and is the dimensionless free surface deflection. Substituting Equation (15) into Equation (14) and making all necessary partial derivatives, we obtain
The boundary conditions become
Equation (15) is third-order, nonlinear, boundary value problem with the Froude number, Fr, as the eigenvalue. In Equation (15) is the wave number, is the capillary-buoyancy coefficient, z is the dimensionless wave velocity, and Re is the film Reynolds number, (flow rate).
To make advantage of the cyclic boundary conditions and due to the nature of the wavy flow, a solution in the form of a Fourier series is suggested.
As seen, this solution satisfies the periodic boundary conditions (16).
Substituting Equation (18) into Equation (15), we get the following algebraic equation.
Equation (19) involves 2N + 1 unknowns, An, Bn and the Froude number as the eigenvalue. Thus we need 2N + 1 equations. This can be achieved by satisfying Equation (19) at 2N + 1 collocation points. The uniform grid is a good choice for the Fourier series.
In the physical problem, one need only specify the Reynolds number, Re, (flow rate), and the capillary-buoyancy coefficient, γ. The values for z and are given by Pierson and Whitaker [
.
Since Equation (15) is an eigenvalue problem in Fr, the solution is not unique and we have troubles finding the solutions. Some examples of the solutions obtained for water are shown in
These wave profiles are unrealistic because the wave amplitude exceeds the boundary at.
Figures 4 and 5 show the wave profile for water (γ =
3400 at Reynolds number, Re = 100, z = 2.8, a = 0.021645).
These realistic sinusoidal-like waves represent the waves appearing at the wave-inception line. This range of Reynolds number studied is of most practical importance in the absorption cooling system. For higher Reynolds number, Pierson and Whitaker’s [
The wave profiles for thin, laminar, gravity-driven, flow are obtained for Reynolds numbers Re = 25, Re = 100, this range of Reynolds numbers are of the most practical importance in the absorption cooling absorber. The proposed hybrid analytical-numerical method combining Fourier series and collocation method makes advantage of periodic boundary conditions and the nature of the sinusoidal type waves appearing in such films. We had great troubles in obtaining the solutions. These solutions are much affected by the initial guess. Another problem we faced was the presence of multiple solutions. Most of these solutions are mathematically correct but physically are not that means that they give unrealistic profiles. It is observed that realistic wave profiles are always obtained once we approach the Froude number corresponding to Nusselt smooth film. Deviation from Froude number for smooth film gives an unrealistic wave profile. The results are good for Reynolds number less than 100. For Reynolds number greater than 100, the solutions are obtainable but we are not interested in besides they may not be realistic due to the invalidity of the linear stability theory at this range as well as the uncertainty in the parabolic velocity profile assumption.
The authors would like to thank the Deanship of Scientific Research, Salaman Bin AbduAlziz University, Kingdom of Saudi Arabia for their support to this research under contract No. 8/h/1432.
= coefficients of expansion in Equation (18)
= wave velocity (m/s)
= Froude number
= gravitational acceleration (m/s2)
= local film thickness (m)
= mean film thickness over a wavelength (m)
= pressure in liquid (N/m2)
= pressure in gas (N/m2)
= Reynolds number =
= time(s)
= x-direction velocity (m/s)
= y-direction velocity (m/s)
= x-direction mean velocity over film thickness
= characteristic velocity (m/s)
= Weber number
= coordinate parallel to the wall
= coordinate normal to the wall
= dimensionless wave velocity
= wave number
= mean volumetric flow rate over a wavelength (m3/s)
=
= wavelength (m)
= kinematic viscosity (m2/s)
=
= liquid density (kg/m3)
= surface tension (N/m)
= dimensionless free surface deflection