Materials Sciences and Applications
Vol.07 No.01(2016), Article ID:63242,6 pages
10.4236/msa.2016.71003

Carbon-13 Solid State NMR Techniques to Evaluate the Morphology of PP/TiO2 Composites

Igor Lopes Soares1, Maria Inês Bruno Tavares1, André Luis B. B. e Silva2,3, Antonio Gabriel Malagueta Feio3

1Instituto de Macromoléculas, Universidade Federal do Rio de Janeiro, Rio de Janeiro, Brazil

2Instituto Federal do Mato Grosso, IFMT, Mato Grosso, Brazil

3CENIMAT/I3N, Departamento de Ciência dos Materiais, Faculdade de Ciências e Tecnologia, Universidade Nova de Lisboa, Caparica, Portugal

Copyright © 2016 by authors and Scientific Research Publishing Inc.

This work is licensed under the Creative Commons Attribution International License (CC BY).

http://creativecommons.org/licenses/by/4.0/

Received 22 October 2015; accepted 26 January 2016; published 29 January 2016

ABSTRACT

Solid state NMR was successfully used to determine the proton spin-lattice relaxation time in the rotating frame (T1ρH) for systems based on polypropylene (PP) and PP with titanium dioxide (TiO2) organically modified or unmodified incorporated, in order to understand the molecular behavior of these systems. These techniques were employed in the samples organically modified and unmodified TiO2 to investigate the effect of organic modification on the dispersion and distribution of the particles in the PP matrix. The results were analyzed in terms of the effect of the particles organic modified or not according to the intermolecular interaction in the composites. According to the T1ρH values, all composites showed at least two domains: the short values were related to the rigid part, which included the crystalline and amorphous phase constricted in it, while the longer times were attributed to the amorphous region, which had higher molecular mobility compared to the rigid region of the materials. The increase in the relaxation time parameter in the composites compared to the pure PP was associated to the strong interaction between titanium dioxide particles and the polymer chains. This effect was more pronounced for the systems containing organically modified TiO2. According to the results, it could be inferred that intermolecular interaction occurred in the CH2 and CH groups, being more intense with CH2 groups. Finally, the solid state NMR techniques were able to evaluate the molecular dynamics of those systems.

Keywords:

NMR, PP, TiO2, Composites

1. Introduction

Solid-state nuclear magnetic resonance is a non-destructive spectroscopy and it comprises many techniques and also permits us to analyze several nucleuses that contain different information on materials, especially polymer and their derivative materials [1] -[5] . Carbon-13 is an important nucleus that gives many responses on polymer chemical structure, arrangements, configurational and is specific to evaluate the molecular dynamics of polymers and materials based on it [6] -[11] . According to this statement, in this work, we have chosen to use the solid-state carbon-13 NMR spectroscopy as a tool to evaluate the systems formed by PP and titanium oxide modified or not, in order to obtain response on the molecular interaction between polymer and particles and also the way that the particles are dispersed and distributed.

The combination of solid state carbon-13 NMR techniques such as: magic angle (13C MAS); spinning cross polarization magic angle spinning (13C CPMAS) and variable contact time (VCT) together with the measurement of proton spin-lattice relaxation time in the rotating frame, with a time constant T1ρ, will give many important information on polymer systems about intermolecular interactions and particles dispersion and distribution. The spin-lattice relaxation in the rotating frame can be determined through the decay of the resolved carbons during the variable contact time experiment under spin-lock conditions that generate a rotating magnetic field near the resonant frequency perpendicular to the static magnetic field [12] - [18] .

The hydrogen MAS also is an important technique to help the evaluation of chains molecular dynamics and together with the carbon-13 NMR responses allow to understand the behavior of polymer systems [19] [20] .

The first objective of this work is preparing PP/TiO2 composites and nanocomposites using TiO2 with or without organic surface modification with hexylamine, seeking materials with characteristics of photodegradation or photostabilization. The second main objective is to use the combination of solid-state nuclear magnetic resonance techniques as a tool to evaluate the PP/TiO2 systems, in their forms, according to the particles dispersion, distribution and their influence on polymer systems organization and morphology.

2. Experimental

2.1. Sample Preparations

The PP/TiO2 composites and nanocomposites were initially prepared by physical mixing of the polymer and particles in a Tepron mixer at a rotation speed of 5 rpm for 30 min, using different TiO2 particle concentrations: 0.25% (w/w), 0.50% (w/w), 0.75% (w/w), 1.0% (w/w). Modified and unmodified TiO2 particles were used to assess the influence of the chemical modification in the compatibility of polymer and particle, to disperse and distribute them in the polymer matrix. The sample codes are listed in Table 1. The composites and nanocomposites were prepared by the melt method in a single-screw extruder (AX Plásticos model AX 1626) with L/D ratio of 26 and screw diameter of 16 mm, containing three heating zones, coupled to a traditional bath and pelletizer. The processing parameters were temperatures of 160˚C, 170˚C and 190˚C, referring to the feed, compression and homogenization zones, respectively, rotation of 40 rpm and pelletizing rate of 19%. The matrix used was the conventional type for production of pellets. The pure PP was prepared in the same way to provide a standard for comparison with the nanocomposites obtained [21] .

2.2. Characterization

2.2.1. Differential Scanning Calorimetry (DSC)

The DSC curves of the samples were obtained under N2, calibrated with an indium standard. The analysis

Table 1. T1H values for TiO2, TiO2 modified with propionic acid and TiO2 modified with propionic acid and octadecyl amine.

involved a first heating from 10˚C to 200˚C followed by fast cooling (100˚C/min), followed by another heating cycle of 20˚C/min, from 20˚C to 240˚C.

2.2.2. X-Ray Diffraction (XRD)

X-ray analyses were done in a Rigaku D/Max 2400 diffractometer, with nickel-filtered CuKα radiation of wavelength 1.54 Å, at room temperature. The 2θ scanning range varied from 2˚ to 30˚, with 0.05˚ steps, operating at 40 KV and 30 mA.

2.2.3. Nuclear Magnetic Resonance Spectroscopy (NMR)

The NMR acquirements were obtained using a Bruker 300AVANCE NMR spectrometer, operating at 75 MHz for carbons detection and 300 MHz for proton detection. Protonspectra were obtained by accumulating 8 K data points over a spectral width of 4400 Hz, using a 7.0 μs, 90 pulse with a recycle delay of 4 s between acquisitions. 13C NMR, spectra were obtained with accumulation of 32 K data points covering a spectral width of 22 000 Hz, and a 5 μs, 90 pulse.

3. Results and Discussion

3.1. DSC

Based on DSC results, the melting temperatures (Tm) and the crystalline temperature (Tc) of the studied PP systems were determined to evaluate the possible changes in their values related to PP. The values of these thermal parameters for pure PP were 161˚C and 121˚C, respectively. Analyzing the materials prepared with PP and TiO2 modified or not, the thermal parameters of the polymer matrix did not change, which is an indication that the particles did not influence processing stability and no degradation was detected.

2.2. XRD

Figure 1 exhibits the X-ray diffratograms of TiO2, unmodified particle and particle modified with propionic acid and octadecyl amine.

The crystallinity degree of the materials containing unmodified TiO2 did not change significantly, in a while for the materials prepared with organically modified TiO2 changes, it increases for the samples containing 0.25% of organic modification and for the others proportions does not change significantly. We believe that the small proportion of organically modified TiO2 could act as a nucleant particles, being nuclei for the matrix growth.

Figure 1. X-ray diffractogram of TiO2, unmodified particle and par- ticle modified with propionic acid and octadecyl amine.

2.3. NMR

Organically modified and unmodified TiO2 nanoparticles were used to investigate the effect of organic modification on their dispersion and distribution in the PP matrix. The molecular dynamic behavior of the PP/TiO2 composites gives information on the microstructure of the composites. The NMR results were analyzed in terms of the effect of the organic modification of the particles and the intermolecular interactions within the composites.

Table 1 listed the T1H values for TiO2, TiO2 modified with propionic acid and TiO2 modified with propionic acid and octadecyl amine (C-18).

The proton spin-lattice relaxation time values presented the same behavior than X-ray and thermal degradation temperature.

The behavior of T1ρH for CH2 and CH3 group for all samples is shown in Figure 2, while that Figure 3 and Figure 4 shown the behavior of T1ρH decay for CH2 and CH3 groups as function of B1 strength for sample PPm0.5% and for sample PPN1%, respectively.

Figure 2. T1ρH behavior for CH2 and CH3 group for all samples.

Figure 3. The behavior of T1ρH decay for CH2 and CH3 groups as function of B1 strength for sample PPm0.5%.

Figure 4. The behavior of T1ρH decay for CH2 and CH3 groups as function of B1 strength for sample PPN1%.

According to the measured T1rH values, all composites showed at least two dynamic domains: the short values were related to the rigid part of the system, which includes the crystalline and the highly constrained amorphous phase, while the longer relaxation times were attributed to the less constrained amorphous region, which has higher molecular mobility compared to the rigid region of the materials.

For all systems, the dispersion and distribution of the particles in the polymer matrix was detected. The increase in the relaxation time parameter in the composites compared to the pure PP was associated to the strong interaction between titanium dioxide particles and the polymer chains. This effect was more pronounced for the systems containing organically modified.

The increase of relaxation times values in the composite materials compared to the pure PP was associated to the strong interaction between titanium dioxide nanoparticles and the polymer chains. This effect was more pronounced for the systems containing organically modified TiO2.

Conclusions

TiO2 particles were organically modified; these treatments promoted an improvement in the interaction and consequently the dispersion of this nanoparticle in the polymer system. Thus, the best PP/TiO2 sample contained with 0.50% of modified particles.

According to all results, it could be inferred that intermolecular interactions occurred mainly with CH2 and CH groups, being more intense with CH2 groups.

Finally, the solid state high resolution NMR techniques were able to evaluate the proton resolved molecular dynamics of those systems.

Acknowledgements

The authors thank you the CAPES, CNPQ and FAPERJ for all financial support of this work and for the scholarship.

Cite this paper

Igor LopesSoares,Maria Inês BrunoTavares,André Luis B. B. eSilva,Antonio Gabriel MalaguetaFeio, (2016) Carbon-13 Solid State NMR Techniques to Evaluate the Morphology of PP/TiO2 Composites. Materials Sciences and Applications,07,20-25. doi: 10.4236/msa.2016.71003

References

  1. 1. Abragam, A. (1996) Principles of Nuclear Magnetism. Oxford Science Publications, Oxford.

  2. 2. Chandrakumar, N. and Subramanian, S. (1987) Modern Techniques in High-Resolution FT-NMR. Springer-Verlag, New York, 388.
    http://dx.doi.org/10.1007/978-1-4612-4626-8

  3. 3. Gil, V.M.S. and Geraldes, C.F.G.C. (1987) Ressonancia Magnética Nuclear: Fundamentos, Métodos e Aplica??es. Funda??o Calouste Gulbenkian, Lisboa, 1012.

  4. 4. Slichter, C.P. (1990) Principles of Magnetic Resonance. Springer-Verlag, New York, 665.
    http://dx.doi.org/10.1007/978-3-662-09441-9

  5. 5. Stejskal, E.O. and Memory, J.D. (1994) High Resolution NMR in the Solid State., New York, 189.

  6. 6. Bovey, F.A. and Mirau, P.A. (1996) NMR of Polymers. Academic Press.

  7. 7. Koenig, J.L. (1992) Spectroscopy of Polymer. American Chemical Society, Washington, 328.

  8. 8. Komoroski, R.A. (1986) High Resolution NMR Spectroscopy of Synthetic Polymers in Bulk. Methods in Stereochemical Analysis, 7, 379.

  9. 9. Lyerla, J.R. and Yannoni, C.S. (1983) High-Resolution Carbon-13 NMR of Polymers in the Solid State. IBM Journal of Research and Development, 27, 302-312.
    http://dx.doi.org/10.1147/rd.274.0302

  10. 10. Schmidt-Rohr, K. and Spiess, H.W. (1994) Multidimensional Solid-State NMR and Polymers. 1st Edition, Vol. 1, Academic Press, London, 478.

  11. 11. Silvestri, R.L. and Koenig, J.L. (1993) Applications of Nuclear Magnetic Resonance Spectrometry to Solid Polymers. Analytica Chimica Acta, 283, 997-1005.
    http://dx.doi.org/10.1016/0003-2670(93)80261-I

  12. 12. Berns, A.E. and Conte, P. (2011) Effect of Ramp Size and Sample Spinning Speed on CPMAS 13C NMR Spectra of Soil Organic Matter. Organic Geochemistry, 42, 926-935.
    http://dx.doi.org/10.1016/j.orggeochem.2011.03.022

  13. 13. Silva, N.M., Tavares, M.I.B. and Stejskal, E.O. (2000) 13C-Detected 1H Spin Diffusion and 1H Relaxation Study of Multicomponent Polymer Blends. Macromolecules, 33, 115-119.

  14. 14. Tavares, M.I.B. (2000) NMR Molecular Dynamic Study of High Crystalline Polymers. Polymer Testing, 19, 899-904.
    http://dx.doi.org/10.1016/S0142-9418(99)00060-4

  15. 15. Nogueira, M.C.J.A., Tavares, M.I.B. and Nogueira, J.S. (2004) 13C NMR Molecular Dynamic Investigation of Tropical Wood Angelin Pedra (Hymenolobium paetrum). Polymer, 45, 1217-1222.
    http://dx.doi.org/10.1016/j.polymer.2003.12.031

  16. 16. Nogueira, R.F., Tavares, M.I.B. and San Gil, R.A.S. (2004) Carbon-13 Solid State NMR Study of Polypropylene/Clay Nanocomposite. Journal of Metastable and Nanocrystalline Materials, 22, 71-76.
    http://dx.doi.org/10.4028/www.scientific.net/JMNM.22.71

  17. 17. Tavares, M.I.B, Nogueira, R.F., San Gil, R.A.S., Preto, M., Silva, E.O., Silva, M.B.R. and Miguez, E. (2007) Polypropylene-Clay Nanocomposite Structure Probed by H NMR Relaxometry. Polymer Testing, 26, 1100-1102.
    http://dx.doi.org/10.1016/j.polymertesting.2007.07.012

  18. 18. Monteiro, M.S.S.B., Silva, E.O., Rodrigues, C.L., Cucinelli Neto, R.P. and Tavares, M.I.B. (2012) The Structure of Polycaprolactone-Clay Nanocomposites Investigated by 1H NMR Relaxometry. Journal of Nanoscience and Nanotechnology, 12, 7307-7313.
    http://dx.doi.org/10.1166/jnn.2012.6431

  19. 19. Passos, A.A., Tavares, M.I.B., Cucinelli Neto, R.P., Moreira, L.A. and Ferreira, A.G. (2011) Preparation of EVA/Silica Nanocomposites Characterized with Solid State Nuclear Magnetic Resonance. Polímeros, 21, 98-102.
    http://dx.doi.org/10.1590/S0104-14282011005000023

  20. 20. Olejniczak, S., Ka?mierski, S., Pallathadka, P.K. and Potrzebowski, M.J. (2007) A Review on Advances of High-Resolution Solid State NMR Spectroscopy in Structural Studies of Polymer/Clay Nanocomposites. Polimery, 52, 713-792.

  21. 21. Soares, I.L., Chimanowsky, J.P., Luetkmeyer, L., Silva, E.O., Souza, D.H.S. and Tavares, M.I.B. (2015) Evaluation of the Influence of Modified TiO2 Particles on Polypropylene Composites. Journal of Nanoscience and Nanotechnology, 15, 5723-5732.
    http://dx.doi.org/10.1166/jnn.2015.10041